Filter
Top Products
xStack
®
DES-3200 Series Layer 2 Managed Fast Ethernet Switch CLI Reference Guide
90
<hex 0x0-0xffff> - Enter the TCP source port mask value here.
dst_port - (Optional) Specify the value of the IPv6 Layer 4 TCP destination port.
<value 0-65535> - Enter the TCP destination port value here. This value must be
between 0 and 65535.
mask - Specify an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the TCP destination port mask value here.
udp - (Optional) Specify to configure the UDP parameters.
src_port - Specify the value of the IPv6 Layer 4 UDP source port.
<value 0-65535> - Enter the UDP source port value here. This value must be between
0 and 65535.
mask - Specify an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the UDP source port mask value here.
dst_port - Specify the value of the IPv6 Layer 4 UDP destination port.
<value 0-65535> - Enter the UDP destination port value here. This value must be
between 0 and 65535.
mask - Specify an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the UDP destination port mask value here.
icmp - (Optional) Specify to configure the ICMP parameters used.
type - (Optional) Specify that the rule applies to the value of ICMP type traffic.
<value 0-255> - Enter the ICMP type traffic value here. This value must be between 0
and 255.
code - (Optional) Specify that the rule applies to the value of ICMP code traffic.
<value 0-255> - Enter the ICMP code traffic value here. This value must be between 0
and 255.
port - Specify the port list used for this configuration.
<portlist> - Enter a list of ports used for the configuration here.
all - Specify that all the ports will be used for this configuration.
vlan_based - Specify that the rule will be VLAN based.
vlan - Specify the VLAN name used for this configuration.
<vlan_name> - Enter the VLAN name used for this configuration here.
vlan_id - Specify the VLAN ID used for this configuration.
<vlanid 1-4094> - Enter the VLAN ID used here. This value must be between 1 and
4094.
permit - Specify that packets matching the access rule are permitted by the Switch.
priority - (Optional) Specify that the priority of the packet will change if the packet matches
the access rule.
<value 0-7> - Enter the priority value here. This value must be between 0 and 7.
replace_priority - (Optional) Specify that the 802.1p priority of the outgoing packet will be
replaced.
replace_dscp_with - (Optional) Specify that the DSCP of the outgoing packet is changed with
the new value. If using this action without an action priority, the packet will be sent to the
default TC.
<value 0-63> - Enter the replace DSCP with value here. This value must be between 0
and 63.
replace_tos_precedence_with - (Optional) Specify that the IP precedence of the outgoing
packet is changed with the new value. If used without an action priority, the packet is sent
to the default TC.
<value 0-7> - Enter the replace ToS precedence with value here. This value must be
between 0 and 7.
counter - (Optional) Specify whether the ACL counter feature is enabled or disabled. This
parameter is optional. The default option is disabled. If the rule is not bound with the
flow_meter, all matching packets are counted. If the rule is bound with the flow_meter, then
the “counter” is overridden.
enable - Specify that the ACL counter feature will be enabled.
disable - Specify that the ACL counter feature will be disabled.
mirror - Specify that packets matching the access rules are copied to the mirror port.
deny - Specify that packets matching the access rule are filtered by the Switch.
time_range - (Optional) Specify the name of the time range entry.
<range_name 32> - Enter the time range name here. This name can be up to 32 characters
long.