358 iSeries and AS/400e System Builder
3575 model matrix summary
Model Capacity Capacity Cartridges Drives
L06 300 GB 900 GB 60 2
L12 600 GB 1.8 TB 120 2 to 4
L18 900 GB 2.7 TB 180 2 to 6
L24 1.2 TB 3.6 TB 240 2 to 6
L32 1.6 TB 4.8 TB 324 2-6
Notes:
14 cartridge slots can be configured for bulk I/O within the library. This reduces the maximum cartridges per library by 14 and
reduces the maximum capacity of the library.
Model L12 can be upgraded to Model L18 to increase the capacity of the library.
Model L24 can be upgraded to Model L32 to increase the capacity of the library.
All drives installed at the plant are 3570 Model C tape drives.
The IBM marketing configurator allows only one drive per IOP port to enable maximum performance. Installing more than one
3570 Magstar MP Model C tape drive on an IOP port might impact system performance. When using the #6501 Tape/Disk Device
Controller to attach the 3575, one port on the #6501 must remain unused.
IBM TotalStorage 3582 Ultrium Tape Library
3582 L23
#8103
#8104
#8105
#8203
#8204
#8205
#5096
#5099
#5301
#5302
3582 Ultrium Tape Library
The IBM 3582 Ultrium Tape Library is designed for desktop operation, but an optional rack mounting kit allows
installation into an ANSI/EIA standard 19-inch rack with four EIA units of space. The 3582 tape library can have one
or two IBM LTO Ultrium 2 tape drives. Ultrium 2 drives have a native data transfer rate of 35 Mbps and cartridge
capacity of 200 MB. Data compression (LTO-DC) provides an effective data rate of 70 Mbps and up to 400 MB
cartridge capacity. The 3582 has two 7-cartridge removable magazines, nine rear fixed slots, and one I/O slot for a
total of 24 tape cartridge slots, providing a maximum capacity of 9.6 TB. Multipath architecture allows the 3582 to be
partitioned into two logical libraries.
Tape drive features:
LTO Ultrium 2 LVD Drive Sled (HD68 connection)
LTO Ultrium 2 HVD Drive Sled (HD68 connection)
LTO Ultrium 2 Fibre Drive Sled with a LC Fibre Channel interface
These are plant only features and cannot be intermixed. Each feature can be ordered by specifying quantity one or
two.
LTO Ultrium 2 LVD Drive Sled (HD68 connection)
LTO Ultrium 2 HVD Drive Sled (HD68 connection)
LTO Ultrium 2 Fibre Drive Sled with a LC Fibre Channel interface
These features provide a second drive that is
client installed. They can be specified with the initial order or ordered
as an MES. One of these features can be intermixed with one #8103, #8104, or #8105 in any combination.
Adapters supported:
LVD Drive Sled (#8103 or #8203)
#5702 PCI-X Ultra Tape Controller, #5705 PCI-X Tape/DASD Controller,
#5712 PCI-X Tape/DASD Controller (LVD, VHDCI), #5715 PCI-X Tape/DASD Controller (LVD, VHDCI)
HVD Drive Sled (#8104 or #8204)
#2729 PCI Magnetic Media Controller (HVD, HD68)
#2749 PCI Ultra Magnetic Media Controller (HVD, HD68)
#6534 Magnetic Media Controller (HVD, HD68)
Fibre Drive Sled (#8105 or #8205)
#2765 PCI Fibre Channel Tape Controller (LC)
#5704 PCI-X Fibre Channel Tape Controller (LC)
Cable features:
Interposer SC-LC
VHDCI/HD68 Cable/Interposer
0.4 m HD68/HD68 SCSI cable (use to daisy-chain two tape drives on the same SCSI bus)
2.5 m (8-ft) HD68/HD68 SCSI cable
