Chapter 5. IBM AS/400e 720, 730, and 740 models 167
#2811 #2811 PCI 25 Mbps UTP ATM IOA (PCI or SPD)
The #2811 provides attachment into an ATM network using Unshielded Twisted Pair (UTP) cabling. The #2811 is used
typically where 25 Mbps speed is required over distances of less than 100 meters.
Prerequisite: #2809 PCI LAN/WAN/Workstation IOP (when located in PCI slot); #2810 LAN/WAN IOP (when located in an
SPD slot)
SPD slots required: One (with #2810)
High-speed PCI slots required: One
#2812 #2812 PCI 45 Mbps Coax T3/DS3 ATM IOA (PCI or SPD)
The #2812 provides attachment into an ATM network using coax cabling and the T3/DS-3 interface. The #2812 is used
typically where 45 Mbps speed is required over distances of less than 1000 meters.
Prerequisite: #2809 PCI LAN/WAN/Workstation IOP (when located in PCI slot); #2810 LAN/WAN IOP (when located in an
SPD slot)
SPD slots required: One (with #2810)
High-speed PCI slots required: One
#2815 #2815 PCI 155 Mbps UTP OC3 ATM IOA (PCI or SPD)
The #2815 provides attachment into an ATM network using the UTP-5 interface. This interface is intended for connection
to both local area switches and direct connection to service provider equipment. The #2815 is used typically where 155
Mbps speed is required over distances of less than 100 meters.
Prerequisite: #2809 PCI LAN/WAN/Workstation IOP (when located in PCI slot); #2810 LAN/WAN IOP (when located in an
SPD slot)
SPD slots required: One (with #2810)
High-speed PCI slots required: One
#2816 #2816 PCI 155 Mbps MMF ATM IOA (PCI or SPD)
The #2816 provides attachment into an ATM network using the Multi-Mode Fiber (MMF) 62.5 micron interface. This
interface is intended for connection to both local area switches and direct connection to service provider equipment. The
#2816 is used typically where 155 Mbps speed is required over distances of less than 2 kilometers.
Prerequisite: #2809 PCI LAN/WAN/Workstation IOP (when located in PCI slot); #2810 LAN/WAN IOP (when located in an
SPD slot)
SPD slots required: One (with #2810)
High-speed PCI slots required: One
#2818 #2818 PCI 155 Mbps SMF OC3 ATM IOA (PCI or SPD)
The #2818 provides attachment into an ATM network using the Single Mode Fibre (SMF) 9 micron interface. This interface
is intended primarily for direct connection to service provider equipment, but can be used for local area switches. The
#2818 is used typically where 155 Mbps speed is required over distances of from 16 to 40 kilometers.
Prerequisite: #2809 PCI LAN/WAN/Workstation IOP (when located in PCI slot);#2810 LAN/WAN IOP (when located in an
SPD slot)
SPD slots required: One (with #2810)
High-speed PCI slots required: One
#2819 #2819 PCI 34 Mbps Coax E3 ATM IOA (PCI or SPD)
The #2819 provides attachment into an ATM network using coax cabling and the E3 interface. The #2819 is used typically
where 34 Mbps speed is required over distances of less than 1000 meters.
Prerequisite: #2809 PCI LAN/WAN/Workstation IOP (when located in PCI slot); #2810 LAN/WAN IOP (when located in an
SPD slot)
SPD slots required: One (with #2810)
High-speed PCI slots required: One
