Chapter 7. IBM iSeries 820, 830, and 840 features and placement 267
#2806
(cont.)
#2806 PCI Quad Modem (CIM)
The call waiting and modem on hold functions associated with V.92 are not supported.
Remote Power On through ring-indicator, SDLC, and synchronous PPP are not supported.
PCI card slots required: One
Minimum operating system level: OS/400 V5R1 with PTFs identified in Information APAR II13079 at:
http://www-912.ibm.com/supporthome.nsf/document/10000035
The #2806 is a Customer Install Feature.
#2817 #2817 PCI 155 Mbps MMF ATM IOA
The #2817 is a 155 Mbps Asynchronous Transfer Mode (ATM) PCI card that allows the server to be attached to an ATM
network using the Multi-Mode Fiber (MMF) 62.5 micron interface. This interface is intended for connection to both local area
switches and direct connection to service provider equipment. The #2817 is used typically where 155 Mbps speeds are
required over distances of less than 2km.
The #2817 is capable of supporting both multiple emulated LAN environments and enhanced TCP/IP performance with
OS/400 V5R1. The #2817 is a 64-bit card, but is allowed to plug into any 32-bit or 64-bit slot. Feature maximums can be
limited when used in combination with other LAN/ATM IOPs.
PCI card slots required: One
Supported on Models 820, 830, 840
Minimum operating system level: OS/400 V5R1.
The #2817 is a Customer Install Feature.
#2849
#9749
#2849 10/100 Mbps Ethernet Adapter
The #2849 10/100 Mbps Ethernet Adapter allows an iSeries server to attach to standardized 100 Mbps high-speed
Ethernet LANs and allows attachment to existing 10 Mbps Ethernet LANs. The adapter comes standard with an RJ45
connector for attachment to UTP-5 media. Cabling for 10 Mbps must be CAT-3 or CAT-5, cabling for 100 Mbps must be
CAT-5 that meets or exceeds Industry Standard EIA/TIA T568A or T568B. Maximum cable length is 100 meters.
The #2849 can be attached directly to a Linux partition. When ordered as #0623 - Linux Direct Attach #2849, an IOP is not
required. When attached directly to a Linux partition, the #2849 cannot be accessed by OS/400 partitions.
Supports LAN console
The #2849 is not supported on any Integrated Netfinity Server or Integrated xSeries Server.
Minimum operating system level: OS/400 V5R2
The #2849 is a Customer Install Feature.
The #9749 was withdrawn from marketing on 01 October 2005.
The #2849 was withdrawn from marketing on 01 June 2006. The #5700 PCI 1 Gbps Ethernet IOA is the recommended
replacement.
#4723 #4723 PCI 10 Mbps Ethernet Adapter
The #4723 PCI Ethernet IOA provides single attachment to one Carrier Sense Multiple Access/Collision Detect Local Area
Network. The feature consists of an adapter card and internal code which supplies Ethernet version 2 and IEEE 802.3 MAC
plus IEEE 802.2 LLC functions. The Ethernet/IEEE 802.3 IOA is capable of operating in half or full duplex mode. The #4723
has an RJ45 connector and a 15-pin D-Shell connector for attachment to client-supplied cabling. A vendor AUI Ethernet
cable or RJ45 twisted pair cable must be ordered separately.
The #4723 is not supported by the #2790 PCI Integrated Netfinity Server or the #2791/#2799 PCI Integrated xSeries
Server.
Minimum operating system level: OS/400 V4R5
The #4723 is a Customer Install Feature.
