354 iSeries and AS/400e System Builder
#5222 Additional 32 LAN Host Attachments
This feature provides an update to the microcode firmware of an installed #5046 or #9046 PCI Library Manager to support
up to 64 LAN attached open system hosts. This is double the 32 LAN attached open system hosts previously available.
This capability is included in the #5047 or #9047 LAN PCI Library Manager. The LAN interface can be through either the
#5220 Ethernet LAN Adapter or the #5219 Token Ring Adapter. Support is provided for up to 32 APPC hosts or 64 TCP/IP
hosts, or combinations of those attachments.
Maximum: One
Prerequisite: #5046 or #9046
#5225 Base Tape Control Unit Attachment
This feature includes an attachment card that provides four RS232 open system host connections and four tape control
unit serial attachments to the 3494 Library Manager. This feature is not required if all open system attached tape drives
are connected to the Library Manager with an EASH attachment, or if LAN attachment to open system hosts is used
instead of an RS232 attachment. If this feature is added to a 3494 that includes Model HA1 Frames, the other Library
Manager must also have this capability.
Maximum: One
Required: If feature #5047 or #9047 is installed and any feature #53xx or #55xx frame is installed on the 3494 Model Lxx
or if the 3494 includes Model HA1 Frames and the other Library Manager has feature #5225, or does not have a #5047
or #9047. Prerequisite: #5047 or #9047
#5226 Remote Console
The #5226 provides the capability of controlling and monitoring the status of up to eight 3494 Tape Library Dataservers
from a remote location using a LAN connection. One #5226 is required per 3494 connected in the LAN.
Maximum: One
#5227 32 Port Attachment
The #5227 provides 16 additional tape control unit connections. Use of this feature along with the #5229 Expansion
Attachment Card provides a total of 24 tape control unit connections and eight RS-232 host processor connections. When
the #5227 is installed with one or two #5228 Tape Control Unit Expansion or with the 3494-HA1 High Availability frame,
the number of available tape control unit connections is increased by 16 over the numbers shown in the following table
for the #5228. This allows up to 32 SCSI or Fibre-Channel attached tape drives to be installed in the library.
Prerequisite: #5229
#5228 Tape Control Unit Expansion
The #5228 expands the number of tape drive controllers that can be attached to the 3494 Library Manager. One feature
converts four RS-232 host processor connections into four tape control unit connections in either the base Library
Manager or the #5229 Expansion Attachment. Up to 128 tape control units can be supported on the Library Manager with
features #5227 and #5184.
Number of #5228 Available RS-232 Available tape control Additional
(for direct attach to host) port connections unit required features
0 4 4 None
0 8 8 #5229
1 0 8 #5219 or #5220
1 4 12 #5229
2 0 16 #5229 and #5219 or #5220
Maximum: Two
#5229 Expansion Attachment Card
The #5229 applies to the Library Manager of the 3494 and is required to support the fifth through eighth tape control units
or the fifth through eighth RS232 connection.
Maximum: One
#5230 Convenience I/O Station (30 Cartridges)
The #5230 allows I/O of up to 30 ½-inch cartridges into the 3494 library without interruption of normal operations.
See the #5210 if 10 cartridge I/O stations are required.
Maximum: One
#5300 Drive Unit
The #5300 provides an expansion unit for an additional CxA tape subsystem and additional 300 cartridge storage
capacity. Attachment to 3494-L10 is supported but attachment to 3494-L12 requires an RPQ.
The #5300 is replaced by 3494 Model D10.
#5302 Upgrade #5300 for 3590-B1A/E1A
The #5302 upgrades #5300 Drive Unit to accept two 3590-B1A or E1A tape drives. RPQ 8B3166 allows a #5300 to accept
a third and fourth drive. RPQ 8B3167 allows #5300 to accept a fifth and sixth drive tape subsystem.
Maximum: One per #5300
