166 iSeries and AS/400e System Builder
#2663 #2663 I/O Attachment Processor (SPD)
The #2663 is an I/O processor required when attaching the #2668 Wireless LAN Adapter. The #2663 and #2668 are
integrated in a single hardware package to operate as a unit.
SPD slots required: One (with #2668 Wireless LAN Adapter)
#2665 Shielded Twisted-Pair Distributed Data Interface Adapter (SPD)
The #2665 provides one interface to connect to an FDDI LAN, which is constructed of IBM Cabling System Type 1, 2, 6,
or 9 shielded twisted-pair wiring. It consists of a card, a wrap connector, and Licensed Internal Code, which supplies IEEE
802.2 LLC, ANSI X3T9.5/ISO 9314 MAC functions and ANSI X3T9.5 SMT functions. IBM FDDI copper jumper cables to
connect the adapter to the FDDI ring must be ordered separately.
SPD slots required: One
#2668 #2668 Wireless LAN Adapter (SPD)
The #2668 Wireless LAN Adapter provides wireless connectivity to workstations or other systems connected to a wireless
LAN network. One of the following antenna cables must be specified:
#9814 20-ft (6 m) antenna cable
#9815 50-ft (15 m) antenna cable
One of the following antenna must be specified:
#9889 YAGI Directional Antenna
#9890 Omni Directional Antenna (360 degrees)
#9891 Hemispherical Antenna (180 degrees)
#9892 Directional Antenna (90 degrees)
SPD slots required: One (with #2663 I/O Attachment Processor)
Prerequisite: #2623 6-Line Communications Controller
#2723
#9723
#2723 PCI Ethernet IOA
The #2723 provides a single attachment to one Carrier Sense Multiple Access/Collision Detect Local Area Network. It
consists of an adapter card and internal code, which supplies Ethernet Version 2 and IEEE 802.3 MAC plus IEEE 802.2
LLC functions. It has a RJ45 connector and a 15-pin D-shell connector for attachment of client-supplied cabling. Cabling
must meet or exceed Industry Standard EIA/TIA T568B. AUI Ethernet or RJ45 twisted pair cable must be ordered
separately.
The #9723 is a base LAN adapter.
The Ethernet/IEEE 802.3 IOA is capable of operating in half or full duplex mode.
PCI slots required: One
#2724
#9724
#2724 PCI 16/4 Mbps Token Ring IOA
The #2724 provides a single attachment to a 16 Mbps or a 4 Mbps Token Ring Network. It consists of an adapter card,
internal code, which supplies IEEE 802.5 MAC and IEEE 802.2 LLC functions, and an external 8-ft (2.4 m) cable.
Alternatively, a twisted pair cable for attachment to the RJ45 connector on the IOA can be ordered separately. The #9724
is a base LAN adapter. The IOA is capable of operating in half or full duplex mode.
PCI slots required: One
#2809 #2809 PCI LAN/WAN/Workstation IOP
The #2809 can be used for attaching PCI LAN, WAN, and workstation IOAs to the system. Refer to the #2809 description
within “Workstation controllers” on page 154 for full information about this controller.
Supported on Model 720
Supported for migration only on the #503x Migration Tower
#2824 #2824 PCI Feature Controller
The #2824 can be used for attaching PCI LAN, WAN, and workstation IOAs to the system. Refer to the #2824 description
within “Workstation controllers” on page 154 for full information about this controller.
#2810 #2810 LAN/WAN IOP (SPD)
The #2810 is required to attach one #2838 PCI 100/10 Mbps Ethernet IOA or the #2811, #2812, #2815, #2816, #2818, or
#2819 PCI ATM IOA on an SPD Bus. The #2810 is a high workload IOP and has configuration limitations.
Prerequisite: They can alternatively be located directly in an appropriate PCI slot.
SPD slots required: One
The #2810 was withdrawn from marketing on 31 May 2001.
