EQQV013E EQQV016E
EQQV013E ACB EXLST BUILD PROCESSING FAILED - R15 =
R15
R00 =
R00
Explanation: The GENCB macro request issued to generate a ACB EXLST block did not complete normally.
System action: NCF processing is terminated.
Problem determination: Use the R15 and R00 return codes to determine the cause of the error. For more
information, refer to the appropriate documentation for the VTAM product installed on this MVS/ESA system.
System programmer response: If insufficient main storage was the cause of the failure, increase the region size
and then restart the TME 10 OPC subsystem. For any other cause of the failure, contact your IBM representative.
EQQV014E ACB BUILD PROCESSING FAILED - R15 =
R15
R00 =
R00
Explanation: The GENCB macro request issued to generate the NCF ACB did not complete normally.
System action: NCF processing is terminated.
Problem determination: Use the R15 and R00 return codes to determine the cause of the error. For more
information, refer to the appropriate documentation for the VTAM product installed on this MVS/ESA system.
System programmer response: If insufficient main storage was the cause of the failure, increase the region size
and then restart the TME 10 OPC subsystem. For any other cause of the failure, contact your IBM representative.
EQQV015E VTAM MACRO REQUEST FAILURE - DIAGNOSTIC INFORMATION: NODE=
NODE
, REQUEST=
X'
REQ
' (
NAMEREQ
), RTNCD= X'
RC
' (
DECRC
) FDBK2= X'
FDBK2
' (
DFDBK2
), SSENSMI=
SMI
USENSEI=
USEI
, SSENSEI=
SSEI
R00= X'
R00
', R15= X'
R15
'
Explanation: An error occurred when a VTAM request was executed or scheduled. The variable items in the
message provide diagnostic information and have the following meanings:
NODE NCF application LU-name
REQ VTAM request code in hexadecimal
NAMEREQ VTAM request name
RC RTNCD feedback field value from RPL in hexadecimal
DECRC RTNCD feedback field value from RPL in decimal
FDBK2 FDBK2 feedback field value from RPL in hexadecimal
DFDBK2 FDBK2 feedback field value from RPL in decimal
SMI System sense modifier information from RPL
USEI User sense information from RPL
SSEI System sense information from RPL
R00 Register 0 return code after a VTAM macro request
R15 Register 15 return code after a VTAM macro request.
System action: The action taken depends on the severity of the error situation. NCF attempts to continue
processing, if at all possible. For the most serious errors, such as undefined feedback code, NCF abends with a
dump and user code.
Problem determination: Use the diagnostic information in the message to determine the cause of the error. For
more information, refer to the appropriate documentation for the VTAM product installed on this MVS/ESA system.
System programmer response: Analyze the diagnostic information, and the dump if produced, to determine the
cause of the failure. If this was not a user error, contact your IBM representative.
EQQV016E
NAMEREQ
REQUEST FAILURE - LU/APPLICATION
NODE
NOT FOUND
Explanation: The VTAM
NAMEREQ
request failed to complete successfully because the LU-name
NODE
could not
be found. The most likely reason for the failure is an invalid specification of an LU-name in the SNAHOST keyword of
the TRROPTS initialization statement. Or, the name
NODE
has not been properly defined to VTAM.
System action: NCF processing is terminated.
System programmer response: Review the name specified in the SNAHOST keyword. Make sure that it is correct
and that a counterpart exists in the VTAM definition statements. Correct the items in error and then restart NCF.
Chapter 28. EQQVnnn Messages 285
