Filter
Top Products
14-10
50 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
rinsing
related
Rinse being not put in tub General
consulting
It may appear
when the rinse
agent remains
to clog .
-Did the rinse agent drain immediately or part
to put the rinse is clogged after putting the rinse
agent? - The rinse agent does not drain only
when putting it up to the reamer shaped cap
which is in the box of rinse agent. If clogged take
out the cap and
51 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
rinsing
related
Bubble being remained General
consulting
It may appear
when there
is too much
or too little
laundry.
- If there is too much laundry or vinyl clothes the
detergent is not solved. Reduce the laundry or
take out the vinyl clothes separately.
52 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
water
drain
related
Water being not drained General
consulting
- In this case you are recommended our
engineer’s inspection.
53 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Dehydrating time being
increased again
General
consulting
..Make a comment for
the customer to pre-
pare the memoran-
dum since he can not
be famaliar with the
contents completely.
The vibration
and noise
occur when
the horizon is
broken or the
laundry are
leaned to one
direction. So
It may appear
when the
safety device
is operating to
prevent it.
- If there is too little laundry less than 1KG or
the clothes in the washing tub are severely
entangled it appears.
54 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Washer being worked
for four hours without
stopping
Specifi c
consulting
If the washing
machine
consumes
hours more
than neces-
sary check
whether the
water supply
is too small.
And note that
that the boling
and the drying
course takes
much time.
- Check whether the water supply time is too
much delayed due to the low pressure of water
or boiling or drying is selected. In other cases
request an engineer’s inspection.
55 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Not dehydrating with the
motor being purring after
water is drained
General
consulting
The power
cord for motor
may be cut or
the gear shaft
hardened.
- In this case you are recommended our
engineer’s inspection.
56 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Being stopped with thuds
during dehydration
AS rerecom-
mended
..Make a comment for
the customer to pre-
pare the memoran-
dum since he can not
be famaliar with the
contents completely.
It may ap-
pear when
the horizon
is broken or
there are too
much clothes
to wash.
- check the level of a washing machine.
57 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Not being squeezed well General
consulting
It may appear
when there
are clothes
like vinyl.
-Check whether the vinyl clothes are attached on
to the washing tub so as to prevent the immedi-
ate the outgoing of the moisture to the outside.
Otherwise request an engineer’s inspection.
58 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Water being in at purchas-
ing
AS rerecom-
mended
- There may be remaining water since the prod-
ucts is delivered thorugh the
fi nal products test.
It is normal and you can use it without fear.
59 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
dehydrat-
ing related
Dehydration being not
worked at all
General
consulting
It may ap-
pear when
the interior
components
do not work
properly.
- In this case you are recommended our
engineer’s inspection.
60 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
others Action for water being
freezen in winter
AS rerecom-
mended
It may appear
when the
machine is
used at the
outside or the
veranda.
- pour the warm water on to the tap to take out
the water suppy hose and put the hose in to the
water of approximately 50 degree. And then pour
the water in to the washing box to check whether
the drain is well done.
61 DRUM
WASHER
(MODEL
NAME :
Q1*3*)
others being clogged/foreign
materials
General
consulting
….the drainage hose
clogged or foreign
material inside
- After loosening the water supply hose and
check the inlet of water supply whether there is
foreign material inserted such a soil dust.