Filter
Top Products
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Programming
19
F232179
To Edit an Entire Wash Cycle
Formula
1. Enter PROGRAM Mode. Refer to Entering
Program Mode Section.
2. Press the (∧) keypad until display shows
“CY01”.
3. Press the (∧) or (∨) keypad until cycle to be
edited is displayed.
4. Press START keypad to select the cycle desired.
Refer to Figure 1, showing which cycle number
corresponds to each keypad when in RUN Mode.
Agitation for the Cycle
5. With display showing “CY_x” (x = cycle
number), press the START (Enter) keypad.
6. Display shows either “nor
n” (for normal
agitation), or “GEnt” (for gentle agitation). Refer
to Table 3.
7. Press the (∧) or (∨) keypad to alter the
selection, or the START keypad to continue.
Wash 1 – Wash 4
NOTE: Programming a time other than “00” for
Wash 1 will make the WASH indicator LED light
while this step is running, but NOT in PROGRAM
Mode.
8. The main display shows “USH1” indicating you
are in the Wash segment (number will reflect
selected Wash segment 1-4).
9. Press START (Enter) keypad. Display shows
agitation time during the step: “00” (skips
segment) or 2-30 minutes. Wash 2 agitation’s
time can be 2-20 minutes, 2-15 minutes for Wash
3 and Wash 4, or “00” to skip Wash 2, Wash 3, or
Wash 4. This is the time after the fill and before
the drain and does not include spin time or time
to first reach a programmed temperature (if your
machine is configured for heat).
10. Press the (∧) or (∨) keypad to alter the
selection, or the START (Enter) keypad to
continue.
11. Display shows “CFIL”, “HFIL”, “bFIL” (for
Cold, Hot, or Both [warm]) or “EFIL”.
12. Press the (∧) or (∨) keypad to alter the
selection, or the START (Enter) keypad to
continue.
NOTE: Extra Fill (“EFIL”) possible only if
configured for “EFIL” in SETUP Mode. If
configured, a third fill valve can be controlled.
13. Display shows “LO”, “
nEd”, or “HI” for Low,
Medium, or High water level, respectively.
14. Press the (∧) or (∨) keypad to alter the
selection, or the START (Enter) keypad to
continue.
15. Display shows “SUP0”, “SUP1”, “SUP2”,
“SUP3”, “SUP4”, “SUP5”, “SUP6” or “SUP7”.
Refer to Table 2 for operation of each supply
selection.
16. Press the (∧) or (∨) keypad to alter the
selection, or the START (Enter) keypad to
continue.
NOTE: “SUP5” and “SUP7” appear ONLY if
control is configured for “ESUP” in SETUP Mode.
If the alternate function is selected (“EFIL”), the
output will function as an additional fill valve
signal with a programmable water level. In this
case, extra supply function would NOT be
available.
NOTE: If programmed for “SUP2”, the ADD
BLEACH indicator LED light turns on and if set
up for “bEEP” the buzzer sounds for the first eight
seconds Supply 2 is on.
17. Press the (∧) or (∨) keypad to alter the selection
or START (Enter) keypad to continue.
The leftmost supply compartment (as seen from front
of machine), which can be used for detergent, flushes
during fill cycles whether Supply 1 option is enabled
or disabled. When Supply 1 option is enabled, Supply
1 (S1) output energizes and is available for external
chemical supply if desired. The Supply 2 option
controls the middle compartment, which can be used
for bleach. Supply 3 and Supply 7 options control the
rightmost compartment, which can be used for fabric
softener. Supply 4, Supply 5 and Supply 6 options
control external chemical supplies, as desired.
NOTE: For additional assistance, refer to
installation instructions.
Display Meaning
nor
n 12 seconds forward, 3 seconds pause, 12
seconds reverse, 3 seconds pause and repeat
for the programmed time
GEnt 3 seconds forward, 12 seconds pause, 3
seconds reverse, 12 seconds pause and repeat
for the programmed time
Table 3