Filter
Top Products
28 American Dryer Corp. 113243-1
S.A.F.E. SYSTEM DIAGNOSTICS MESSAGES
OPEN THERMISTOR PROBE This message indicates that
the S.A.F.E. system thermistor probe either is not connected
or is damaged. If this condition is detected, the Phase 7 non-
coin control will immediately enter S.A.F.E. SYSTEM
DISABLED mode.
SHORTED THERMISTOR PROBE This message indicates
that the S.A.F.E. system thermistor probe is damaged or the
wiring is shorted. If this condition is detected, the Phase 7
non-coin control will immediately enter S.A.F.E. SYSTEM
DISABLED mode.
DISCONNECTED WATER VALVE This message indicates
that the water valve is open or that it
is not connected to the
control. If this condition is detected, the Phase 7 non-coin
control will continue to monitor the condition for a period of 5
minutes before entering S.A.F.E. SYSTEM DISABLED mode.
Once the condition is corrected, the control will continue to
monitor the condition for 1 minute before exiting S.A.F.E.
SYSTEM DISABLED mode.
SHORTED WATER VALVE This message indicates that the
water valve is shorted or that the wiring to the valve is shorted.
If this condition is detected, the Phase 7 non-coin control will
continue to monitor the condition for a period of 5 minutes
before entering S.A.F.E. SYSTEM DISABLED mode. Once
the condition is corrected, the control will continue to monitor
the condition for 1 minute before exiting S.A.F.E. SYSTEM
DISABLED mode.
WATER NOT CONNECTED This indicates that there is no
water pressure at the water valve. This will occur if water is
not connected to the dryer, or if there is low water pressure in
the water line coming to the dryer. This could also signify a
defective pressure switch or defective wiring to the pressure
switch. If this condition is detected, the Phase 7 non-coin
control will continue to monitor the condition for a period of 5
minutes before entering S.A.F.E. SYSTEM DISABLED mode.
Once the condition is corrected, the control will continue to
monitor the condition for 1 minute before exiting S.A.F.E.
SYSTEM DISABLED mode.
STARTING A CYCLE WHEN COMPUTER IS IN S.A.F.E.
SYSTEM IS DISABLED MODE
NON-COIN When the S.A.F.E. system is disabled, the user
can still start a cycle. However, when a cycle is started, the
control will display the following message: S.A.F.E. SYSTEM
IS DISABLED. PRESS START TO CONTINUE. This
message will be displayed every time a cycle is started, until
the disabling condition has been corrected.
COIN When the S.A.F.E. system is disabled, the user can
still start a cycle. Simply insert credit and select a cycle to
start.
S.A.F.E. System Parts
Break Down
Replacement parts can be obtained from your reseller or the
ADC factory. When ordering replacement parts from the
factory, you can FAX your order to ADC at (508) 678-9447 or
telephone your order directly to the ADC Parts Department at
(508) 678-9000. Please specify the dryer model number
and
serial number in addition to the description and part
number, so that your order is processed accurately and
promptly.
The illustrations on the following pages may not depict your
particular dryer exactly. The illustrations are composite of the
various dryer models. Be sure to check the descriptions of
the parts thoroughly before ordering.
We have tried to make this manual as complete as possible
and hope you will find it useful. ADC reserves the right to
make changes from time to time, without notice or obligation,
in prices, specifications, colors, and material, and to change
or discontinue models.
Illus. No. Part No. Qty. Description
1 822752 1 S.A.F.E. System Temperature
Probe Assembly
(includes illus. nos. 1 through 5)
2 154007 2 Push On Fastener
3 390390 1 Sensor Bracket ONLY
4 150301 2 #8-18 x 7/16 Phillips Pan Head
TEK Screw
5 122647 1 Connector ONLY
(does not include terminals)