Filter
Top Products
29
The drain hose may be extended to a
maximum of 4 metres. An additional drain hose
and joining piece is available from your local
Service Force Centre. The joining piece must
have an internal diameter of 18mm.
If your drain hose
looks like this (see
below) you do not
require the «U» piece.
Just push the hose
firmly into the
standpipe.
2. Onto a sink outlet spigot.
If the outlet spigot has not been used before,
remove any blanking plug that may be in place.
Push the drain hose onto the spigot and secure
with a clip, ensure a loop is formed in the drain
hose (see diagram) to prevent waste from the
sink entering the washing machine.
Loop
1
0
0
0
6
k
g
40°
30°Rinse
Delicates
ZWF10070W
Off
Special
95°Sport 40°
60° EcoSport Shoes 40°
60°
40° Eco
Silk
40°
50°
40°
Mini 30'
Hand
Wash
Cold
30°
Drain
Spin
Wool
Cottons
Synthetics
Easy Iron 40°
St
a
rt/
P
a
us
e
Wash
Door
End
Ex
tr
a
R
in
s
e
O
p
tio
n
s
Sp
in
1000
900
700
P
re
w
a
sh
In
te
n
si
ve
S
u
p
er
Q
u
ic
k
3h
6h
9h
Min. 60 cm (23.6)
Max. 90 cm (35.4)
30 cm (12")
38 mm (1.5)
standpipe
diameter
1
0
0
0
6
k
g
40°
30°Rinse
Delicates
ZWF10070W
Off
Special
95°Sport 40°
60° EcoSport Shoes 40°
60°
40° Eco
Silk
40°
50°
40°
Mini 30'
Hand
Wash
Cold
30°
Drain
Spin
Wool
Cottons
Synthetics
Easy Iron 40°
S
t
a
r
t
/
P
a
u
s
e
Wash
Door
End
E
x
tr
a
R
i
n
s
e
O
p
t
io
n
s
S
p
in
1000
900
700
P
r
e
w
a
s
h
I
n
t
e
n
s
i
v
e
S
u
p
e
r
Q
u
i
c
k
3h
6h
9h
Important!
Before connecting the machine to new
pipework or to pipework that has not been
used for some time, run off a reasonable
amount of water to flush out any debris that
may have collected in the pipes.
Levelling
Level the washing machine by raising or
lowering the feet. The feet may be tight to
adjust as they incorporate a self locking nut,
but the machine MUST be level and stable.
Any necessary
adjustment can be
made with a spanner.
Accurate levelling
prevents vibration,
noise and
displacement of the
machine during operation.
Some vibration is inevitable, especially if
mounted on a wooden floor.
Sprung wooden floors are particularly
susceptible to vibration. For advice, consult a
builder. If possible, always place the machine
on a solid floor.
Special conditions
If the floor is carpeted or covered with crumbly
or soft material, insert a rigid support base
under the feet to prevent noise, vibration or
displacement. The base should protrude a few
centimetres beyond the edges of the machine.
WARNING!
The machine should NOT be placed on deep
pile carpeting.
NOTE
Please ensure that when the appliance is
installed it is easily accessible for the engineer
in the event of a breakdown.
132964330.qxd 19/06/2008 14.41 Pagina 29