Filter
Top Products
4
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free number
on the cover or in the “Assistance or Service” section.
If You Have You Will Need to
Buy
Laundry tub or
standpipe taller
th
an 96" (2.4 m)
Sump pump system (if not already
available)
Overhead sewer Standard 20 gal. (76 L), 30" (762 mm) tall
drain
tub or utility sink and sump pump
(available from local plumbing suppliers)
Floor drain Siphon break, Part Number 285834;
add
itional drain hose Part Number
8318155; and connector kit, Part
Number 285835
Drain hose too
sho
rt
4 ft (1.2 m) drain hose extension kit,
Part Number 285863
Water faucets
beyon
d reach of fill
hoses
2 longer water fill hoses: 6 ft (1.8 m)
Part Number 76314, 10 ft (3.0 m)
Part Number 350008
Options
Pedestal
You have the option of purchasing pedestals of different heights
separately for this washer. You may select a 10" (254 mm) or a
15
.5" (394 mm) pedestal. These pedestals
will add to the total
height of the washer for a total height of approximately
48" (1219 mm) or 53.5" (1359 mm).
AB
A.10" (254 mm) pedestal
B.15.5" (394 mm) pedestal
To order, call the dealer from whom you purchased your washer or
refer to the “Assistance or Service” section.
Pedestal
Height
Color Part Number
10" (254 mm) White WHP1000SQ
10" (254 mm) Black WHP1000SB
10" (254 mm) Diamond Dust (Silver) WHP1000SU
15.5" (394 mm) White XHP1550VW
15.5" (394 mm) Black XHP1550VB
15.5" (394 mm) Diamond Dust (Silver) XHP1550VU
15.5" (394 mm) New Aspen (Light Green) XHP1550VA
15.5" (394 mm) Tuscan Chestnut XHP1550VC
15.5" (394 mm) Ocean Blue XHP1550VE
15.5" (394 mm) Cranberry Red XHP1550WR
15.5" (394 mm) Lunar Silver XHP1550WL
Stack Kit
Are you planning to stack your washer and dryer? To do so you
will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your dryer or
r
efer to the “Assistance or Service” section. Ask for Part
Number 8541503.
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a
basement, laundr
y room, closet, or recessed area. See “Drain
System.”
Companion appliance location req
uirements should also be
considered. Proper installation is your responsibility.
You will need
■ A water heater set to deliver 120°F (49°C) water to the washer.
■ A grounded electrical outlet located within 6 ft (1.8 m) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
■ Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6 kPa).
■ A level floor with a maximum slope of 1" (25 mm) under entire
washer. Installing the washer on soft floor surfaces, such as
carpets or surfaces with foam backing, is not recommended.
■ A sturdy and solid floor to support the washer with a total
weight (water and load) of 400 lbs (180 kg).
Do not operate your washer in t
emperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in
low temperatures.
Installation clearances
■ The location must be large enough to allow the washer door to
be fully opened.
■ Additional spacing should be considered for ease of
installation and servicing.
■ Additional clearances might be required for wall, door, and
floor moldings.
■ Additional spacing of 1" (25 mm) on all sides of the washer is
recommended to reduce noise transfer.
■ Companion appliance spacing should also be considered.
Pedestal
Height
Color Part Number