Filter
Top Products
20
■ Press WRINKLE PREVENT setting to get up to 90 minutes of heat-free, periodic tumbling
at the end of a cycle.
■ Stop the Wrinkle Prevent at any time by pressing WRINKLE PREVENT setting or opening
the dryer door.
■ For the Wrinkle Control cycle, the Wrinkle Prevent setting is preset to ON. The other
Sensor Cycles will retain the Wrinkle Prevent setting. For example, if you select the
Wrinkle Prevent setting in the Normal cycle, the Wrinkle Prevent setting will be on the
next time you select the Normal cycle.
NOTE: If you do not select the Wrinkle Prevent setting, the dryer stops after cool down.
Damp Dry Signal
Select the Damp Dry Signal to alert you that your clothes are approximately 80% dry. This is
useful when you want to remove lightweight items in a mixed load to avoid overdrying or
remove partially dry items that may need ironing.
The Damp Dry Signal is useful w
hen drying bedsheets/linens in a mixed load. When the
signal goes off, open the door to stop the dryer, rearrange the load inside the dryer, close the
door, and restart the dryer to finish the drying cycle. Rearranging the load will aid in the
drying process.
NOTE: The Damp Dry Signal is available only with the Sensor Cycles.
End Signal
End Signal
The End Signal produces an audible sound when the drying cycle is finished. Promptly
removing clothes at the end of the cycle reduces wrinkling.
Press END SIGNAL until the desired volume (High, Low, or Off) is selected.
NOTE: When the Wrinkle Prevent setting is selected and the End Signal is on, the tone will
sound every 5 minutes until the clothes are removed, or the
Wrinkle Prevent setting ends.
Changing Cycles, Modifiers, and Options
You can change Sensor and Timed Cycles, Modifiers, and Options anytime before pressing
Start.
■ Three short tones sound if an unavailable combination is selected. The last selection will
not be accepted.
Changing Cycles after pressing Start
1. Press POWER/CANCEL.
2. Selec
t the desired cycle and options.
3. Press ST
ART/PAUSE. The dryer starts at the beginning of the new cycle.
NOTE: If you do not press Start/Pause within 5 minutes of selecting the cycle, the dryer
automatically shuts off.
Changing Modifiers and Options after pressing Start
You can change an Option or Modifier anytime before the selected Option or Modifier
begins.
1. Press ST
ART/PAUSE.
2. Select the
new Option and/or Modifier.
3. Press START/PAUSE to continue the cycle.
Changing the Preset Dryness Level Settings
If all of your loads on all Sensor cycles are consistently not as dry as you would like, you may
change the preset Dryness Level settings to increase the dryness. This change will affect all of
your Sensor cycles.
Your Dryness Level settings can be
adjusted to adapt to different installations, environmental
conditions, or personal preference. There are 3 drying settings: 1 (factory preset dryness
lev
el), 2 (slightly dryer clothes, approximately
15% more drying time) and 3 (much dryer
clothes, approximately 30% more drying time).
1. T
he Dryness Level settings cannot be changed while the dryer is running.
2. Press and hold the
DRYNESS LEVEL button for 5 seconds. The dryer will beep, and “CF”
will be displayed for 1 second followed by the current Dryness Level setting.
3. T
o select a new Dryness Level setting, press the DRYNESS LEVEL button again until the
desired Dryness Level setting is shown.
NOTE: While c
ycling through the settings, the current setting will not flash, but the other
settings will flash.
4. Press START/PAUSE to save the Dryness Level setting.
5. T
he Dryness Level setting you selected will become your new preset Dryness Level setting
for all Sensor cycles.
Drying Rack Option
Use the Drying Rack to dry items such as sweaters and pillows without tumbling. The drum
turns, but the drying rack does not move.
If your model does not have a drying rack, you may be able to purchase one for your model.
T
o find out whether your model allows drying rack usage and for information on ordering,
please refer to the front page of the manual or contact the dealer from whom you purchased
your dryer.
NOTE: The drying rack must be removed for normal tumbling. Do not use the automatic cycle
with the drying rack.
To use the drying rack
1. Open dryer door.
A
A.Front edge