Filter
Top Products
Page 5
ENGLISHENGLISH
ENGLISHENGLISH
ENGLISH
ENGLISHENGLISH
ENGLISHENGLISH
ENGLISH
1. Connect the exhaust hose to a ventilation exhaust
fitting or to a discharge through the wall.
2. Secure the hose joint to the outlet stub on the
machine.
3. Run the hose with as few bends as possible to the
point of discharge. If necessary, it can be extended
to a maximum of 20 feet (610 cm) of 4” (10 cm)
diameter ridged pipe.
Make any bends as gentle as possible. A maximum of
four 90° bends may be fitted in the hose. The more
bends and the longer the hose, the less air will circulate
through the machine, which will impede drying
performance. Subtract 4 feet (122 cm) for every 90°
elbow.
NOTE: When installing in warm climates (77° F and
above) with high humidity levels, do not
route the air exhaust hose upwards.
CONNECTING CONNECTING
CONNECTING CONNECTING
CONNECTING
TT
TT
T
O O
O O
O
A A
A A
A
VENTILAVENTILA
VENTILAVENTILA
VENTILA
TION DUCT (T701 TION DUCT (T701
TION DUCT (T701 TION DUCT (T701
TION DUCT (T701
AND AND
AND AND
AND
T761)T761)
T761)T761)
T761)
Subtract 4 feet
(122 cm) for
every 90° elbow.
Ventilation grill
FREESTFREEST
FREESTFREEST
FREEST
ANDING INSTANDING INST
ANDING INSTANDING INST
ANDING INST
ALLAALLA
ALLAALLA
ALLA
TIONTION
TIONTION
TION
The dryer can be placed next to the washing machine.
It is essential that the machine is leveled and the
locknuts are tight to eliminate vibration noise.
ASKO dryers can be installed beneath a cabinet or
worktop with a minimum height of 34” (864 mm). There
must be a gap of about 1/2” (12 mm) all around the
machine, including between the rear edge of the
machine top panel and the back wall. The opening
width must be at least 24-1/2” (622 mm).
Space must also be available for the exhaust hose on
the left, right or rear of the machine. See the diagram for
hole sizes and positions. Note that the hole
measurements are to the center of the hole.
MODELS T721 AND T781
The condensing models work best when they have good
air circulation. Therefore, we don’t recommend they be
installed beneath a cabinet. If it is necessary, however, be
sure to leave a gap of at least 1/2” (12 mm) on all sides.
If you install the dryer so the condensed water will
continuously flow into a drain or sink, you will need a
drain outlet behind the unit. The maximum drain height
is 40” (1016 mm). (See page 4.)
BB
BB
B
UILUIL
UILUIL
UIL
TT
TT
T
-IN INST-IN INST
-IN INST-IN INST
-IN INST
ALLAALLA
ALLAALLA
ALLA
TIONTION
TIONTION
TION
NOTES: The height adjustment for the dryer is
33-1/2” to 34-1/2” (850 mm to 876 mm). Do
not raise it higher than 34-1/2”.
Hole measurements are from center of hole.
Installation Examples
If more than 20 feet of hose is needed, the diameter
must be increased to 6” or 8” (152 mm or 203 mm).
WARNING!
This appliance should not be exhausted into a
chimney, a wall, a ceiling, or a concealed space of a
building. Only a metal ventilation grill should be used.
If the hose is taken to a wall outlet, a ventilation grill
should be fitted to prevent reverse flow of cold air. Fit the
ventilation grill to the outside or inside of the wall.
Vent spacer
Make sure nothing is
blocking the ventilation grill.
If there is only one vent duct from the room, a vent spacer
must be fitted.
220V, 20 Amp
Single Phase
Outlet
4-23/32"
120 mm
5-1/2"
140 mm
4-1/8"
105 mm
5-1/2"
140 mm
24-1/2" minimum
622 mm
34" to 35"
863 to 889 mm
2
5
"
6
3
5
m
m
There should be at least 1/2” (12 mm) of space between
the washer and dryer.