Filter
Top Products
Page 4
Height 33-1/2”–34-1/2 (850–876 mm)
Width 23-7/16” (595 mm)
Plus exhaust hose connection
Depth T761/T781: 23-7/16" (595 mm)
T701/T721: 24-7/16” (620 mm)
Weight 86 lbs (39 kg)
Drum material Stainless Steel
Read these instructions carefully and completely before
you install the machine. The installation should be
carried out by a qualified person who is familiar with all
local codes and ordinances for electrical and plumbing
connections.
SPECIFICASPECIFICA
SPECIFICASPECIFICA
SPECIFICA
TIONSTIONS
TIONSTIONS
TIONS
INSTINST
INSTINST
INST
ALLAALLA
ALLAALLA
ALLA
TION INSTRTION INSTR
TION INSTRTION INSTR
TION INSTR
UCTIONSUCTIONS
UCTIONSUCTIONS
UCTIONS
Outer casing Stove-enamelled hot-dipped
galvanized steel
Power requirement 2800 watts
For connection Single-phase, 230 V, 30 Amp
Internal fuse 15 amp.
Heating element 2500 watts
NOTE: Cosmetic damage must be reported to your
dealer within five days from the date of pur-
chase. After unpacking the dryer, thoroughly
check the unit for cosmetic damage.
The exhaust hose can be connected at the rear or on
either side of the dryer. When the machine is delivered,
the exhaust outlet at the rear is open.
CONNECTING CONNECTING
CONNECTING CONNECTING
CONNECTING
AIR EXHAAIR EXHA
AIR EXHAAIR EXHA
AIR EXHA
UST (T701 UST (T701
UST (T701 UST (T701
UST (T701
AND AND
AND AND
AND
T761)T761)
T761)T761)
T761)
The dryer is shipped with a stub pipe already installed
on the rear exhaust outlet. The consumer or installer
must purchase a UL-CSA-approved exhaust hose.
RR
RR
R
ear Outlet Hose Connectionear Outlet Hose Connection
ear Outlet Hose Connectionear Outlet Hose Connection
ear Outlet Hose Connection
To connect the exhaust hose to the rear outlet, follow
the steps below:
1. Push the hose onto the stub pipe and secure it with
a clamp.
2. With the hose attached, insert the stub pipe into the
hole. It should snap into place.
The exhaust hose
can be connected at
the rear or on either
side of the dryer.
Side Exhaust Outlet
Rear Exhaust Outlet
Stub
Clamp
Hose
(not supplied)
CONDENSACONDENSA
CONDENSACONDENSA
CONDENSA
TION DRAIN CONNECTION (T721 TION DRAIN CONNECTION (T721
TION DRAIN CONNECTION (T721 TION DRAIN CONNECTION (T721
TION DRAIN CONNECTION (T721
AND AND
AND AND
AND
T781)T781)
T781)T781)
T781)
If possible, you should install the dryer so the
condensed water will continuously flow into a drain or
sink. To do this, follow the instructions below:
1. Disconnect the short hose (1) from the blue
connection. (It’s okay to let the hose hang down.)
2. Connect the rubber hose supplied with the dryer to
the blue nipple (2).
3. Run the hose to a drain or sink, as illustrated.
NOTE: The drain hose must not be more than 40”
above the floor.
Back of dryer
Vent
T-Tube
NOTE: After you push the dryer into place, check for
kinks in the hose. (Be careful not to use too
much hose, because it could reduce drying
efficiency.)
CONNECTING THE VENT HOSE TO THE
LEFT OR RIGHT SIDE OUTLET
To connect the exhaust hose to the left or right side
outlet, follow the steps below:
1. Using a flathead screw-
driver, turn the exhaust
outlet cover to align the tabs
holding the cover in place.
Remove the cover.
2. Remove the stub pipe from
the rear exhaust outlet.
3. Place the stub pipe in the
outlet you plan to use.
4. Follow the instructions for the rear outlet hose
connection.
5. Use the exhaust outlet cover you removed from the
side to cover the rear exhaust outlet.
WARNING!
To reduce the risk of fire, this appliance must be
exhausted OUTDOORS or the equivalent.
Never cover the end of the dryer stub or vent hose
with anything to catch lint, except for UL approved
vent basket.