Filter
Top Products
13
7. To begin the wash cycle immediately
Press and hold START/PAUSE (for approximately 1 second).
■ If you do not press START/PAUSE within 5 minutes of
choosing a cycle, the washer automatically shuts off.
■ When the wash cycle is complete, the Done status light
illuminates, the door unlocks, and the wash load can be
removed from the washer. To power down the washer
manually after the wash cycle is complete, press POWER
once or open the door when the DONE status light goes
off.
8. To begin the wash cycle later
Press DELAY START until the desired delay time (in hours) is
dis
played. Press START/PAUSE. The countdown to the wash
cycle will show in the display window.
IMPORTANT: Wh
en delaying a cycle, use only powdered
detergents in the main wash compartment since liquid
detergents may seep out of the compartment during Delay,
before the wash cycle begins.
Using the Dispenser
Your new washer has a dispenser drawer with three separate
compartments for your laundry products—one is for detergent,
one is for liquid chlorine bleach, and one is for liquid fabric
softener. Laundry products are diluted and dispensed
automatically at the proper time during the wash cycle, making it
unnecessary for you to return to the washer during the cycle to
add them.
It is normal for small amounts of water to r
emain in the dispensers
when the wash cycle is complete.
Do not put laundry products directly into the
wash tub. Always
use the proper dispensers when adding laundry products.
Choosing the Right Detergent
Use only High Efficiency detergents. The package for this type of
detergent will be marked “HE” or “High Efficiency.”
This wash
system, along with less water, will create too much sudsing with a
regular non-HE detergent. Using regular detergent will likely result in
washer errors, longer cycle times, and reduced rinsing performance.
It may also result in component failures and noticeable mold or
mildew.
HE detergents are made to produce the right amount of
suds for the best performance. Follow the manufacturer's
instructions to determine the amount of detergent to use.
Use only HE High Efficiency detergent.
To fill dispenser compartments
1. Pull out the dispenser drawer.
2. Add the desired laundry products to the proper compartment.
3. Push
in the dispenser drawer slowly and completely (to avoid
a spill).
A
B
C
D
Dispenser
A.Dispenser release lever
B.Main Wash detergent compartment
C.Liquid chlorine bleach compartment
D.Fabric softener compartment
Main Wash detergent compartment
(Letter B in Dispenser Illustration)
Add liquid or powdered HE detergent to this compartment for
your main wash cycle.
■ Liquid color-safe bleach or oxi products may be added to the
Main Wash compartment along with liquid detergent.
■ Powdered color-safe bleach or oxi products may be added to
the Main Wash compartment along with the powdered
detergent.
■ Do not mix powdered and liquid products in the Main Wash
compartment.
■ Use the measurement device which comes with the detergent.
Add no more than the manufacturer's recommended amount.
NOTE: Overfillin
g could cause an oversudsing condition.
Chlorine bleach compartment
(Letter C in Dispenser Illustration)
Add NO MORE THAN
2
/3 cup (160 mL) liquid chlorine bleach to
this compartment. The bleach will be automatically diluted and
dispensed at the best time during the first rinse after the wash
cycle. This compartment cannot dilute powdered bleach.
■ Use only liquid chlorine bleach in this dispenser. Do not use
this dispenser to add powdered chlorine or any form of color-
safe bleach or oxi products to your load.
■ Always measure liquid chlorine bleach. Use a measuring cup
with a pour spout; do not guess. Follow the manufacturer’s
directions for proper use.
■ Do not fill beyond the “MAX” level.
NOTE: Overfilling could cause garment damage.
Fabric softener compartment
(Letter D in Dispenser Illustration)
Follow the manufacturer's instructions to determine the amount of
fabric softener to use. Fabric softener will be automatically
dispensed in the final rinse or in the Extra Rinse, if selected.
■ Do not fill beyond the “MAX” level.