Filter
Top Products
19
■ Press TEMP until the desired temperature illuminates.
NOTE: Pressing the Dryness Level button will cause the triple beep indicating that this
option is not selectable. Also, a Dryness Level is not indicated.
■ Press the EXTRA CARE feature button if this option is desired.
■ Press the CYCLE END SIGNAL button to set volume to desired level.
■ Press and hold HOLD TO START button until dryer starts (about 1 second).
While a Manual Cycle is running, you can change the settings for Time, Temperature, the
Extra Care feature, and the Cycle End Signal. Press the OFF button twice to stop the dryer
and clear the settings, allowing you to select another cycle.
Stopping Your Dryer
To stop your dryer at any time
Press OFF twice or open the door.
Pausing or Restarting
To pause the dryer at any time
Open the door or press OFF once.
To restart the dryer
Close the door and press and hold HOLD TO START button until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted if you close the door and
press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will
shut off. Select new cycle settings before restarting the dryer.
Control Locked
This feature allows you to lock your settings to avoid unintended use of the dryer. You can also
use the Control Locked feature to avoid unintended cycle or option changes during dryer
operation.
To enable the Control Locked feature when dryer is running:
Press and hold the CYCLE END SIGNAL button for 3 seconds. The control is locked when a
single beep is heard and the Control Locked status light is on.
■ When the dryer is off, it is not necessary to press the Control On button before activating
the Control Locked feature.
To unlock:
Press and hold the CYCLE END SIGNAL button for 3 seconds to turn this feature off.
NOTE: When the dryer is running and Control Locked is on, the dryer can be stopped by
pressing the Off button, but can’t be restarted until the control is unlocked.
Drying and Cycle Tips
Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle
is running, the display shows the estimated cycle time when your dryer is automatically
sensing the dryness level of your load. If a Manual Cycle is running, the display shows the
exact number of minutes remaining in the cycle.
Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool
Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
■ Follow care label directions when they are available.
■ If desired, add a fabric softener sheet. Follow package instructions.
■ Remove the load from the dryer as soon as tumbling stops to reduce wrinkling. This is
especially important for permanent press, knits and synthetic fabrics.
■ Avoid drying heavy work clothes with lighter fabrics. This could cause overdrying of
lighter fabrics, leading to increased shrinking or wrinkling.
Cycle tips
■ Dry most loads using the preset cycle settings.
■ Refer to the Automatic or Manual Preset Cycle Settings chart (in the “Cycles” section) for a
guide to drying various loads.
■ Drying temperature and Dryness Level are preset when you choose an Automatic
Cycle. You can choose a different dryness level, depending on your load by pressing
the DRYNESS LEVEL button to select MORE or LESS.
■ If you wish to adjust the cycle length of a Manual Cycle, you must press the MANUAL
DRY TIME (- or +) buttons. Adjust the temperature of a Manual Cycle by pressing
TEMP until the desired temperature is selected.
NOTE: You cannot choose a Dryness Level with Manual Cycles.
Status Lights
You may follow the progress of your dryer with the drying status indicator lights.
Sensing
When a cycle is first turned on, the Sensing light illuminates until a wet item is detected.
■ In an Automatic Cycle, if a wet item has not been detected within 10 minutes, the Sensing
light will turn off and the dryer will shut down.
■ In a Manual Cycle, if a wet item is not detected after 10 minutes the Wet light turns on
and the selected cycle continues.
Wet
The Wet light will turn on when a wet item has been detected in the dryer. The Wet light will
remain on until:
■ The damp dry point is reached in an Automatic Cycle.
■ The dryer enters the cool down period in a Manual Cycle.