Filter
Top Products
Normal, or I_ess Dry. Selecting More Dry, Normal, or I.ess Dry automatically adjusts
the dryness [eve[ at which the dryer will shut off.
more dry
normal
less dry
sensor cycles ]
dryness
• Press the WRINKI.E PREVENT feature button if this option is desired.
• Press the SIGNAl. ON/OFF button to set the end of cycle signal
• Press and hold START/PAUSE button until dryer starts (about 1 second).
The Wrinkle Prevent and Cycle Signal features can be adjusted during a Sensor Cycle. If
you want to select another Sensor Cycle or Sensor Cycle Dryness, press START/PAUSE once
to stop the dryer, make the desired changes, then press START/PAUSE to resume drying.
NOTES:
A default time is displayed when a Sensor Cycle is selected. During the first few
minutes of the drying process, the cycle time may automatically vary from the default
time based on the size and fabric type of the load. Toward the end of the drying
process, the estimated time display will adjust again, showing the final drying time.
• Time and Temperature are not adjustable for Sensor Cycles. Pressing the TIME
ADJUST or TIMED CYCI_ES TEMP buttons will cause a triple beep, indicating that the
time cannot be changed.
• A light next to each feature will glow yellow when the feature is selected. The light
will not glow when the selection is unavailable with the cycle or option combinations
selected.
• Sensor Cycles Dryness can be changed only with Sensor Cycles. This feature is not
se[ectab[e for Timed, Steam, or Sanitize cycles.
How Sensor Cycles Work
The Sensi-Care TMdrying system improves performance with Auto Moisture Sensing Plus,
which advances the cycle as moisture is extracted from clothing. A thermistor (electronic
temperature sensor) and moisture sensing strips in the dryer drum help measure the
amount of moisture in the clothes as they tumble. An electronic control determines the •
load type to help save time, avoid overdrying, and increase the accuracy of the end
dryness [eve[. After the first 5 minutes of a Sensor cycle, the estimated time display will
adjust based on the approximate load size, cycle, dryness [eve[ selected and amount of
moisture left in the clothes. When the clothes have reached approximately 80% of the •
dryness [eve[ selected, the estimated time display will adjust again, showing the final
drying time. Sensi-Care TMtakes the guesswork out of drying time and enhances fabric
care. •
To use a Timed Cycle
• Press POWER/CANCEl .....
• Rotate the dial to select a Timed Cycle.
• Press the TIME ADJUST up or down buttons until the desired drying time is displayed.
Press TIME ADJUST, and the time will change by 1-minute intervals. Press and hold
TIME ADJUST, and the time will change by 5-minute intervals. The initial time
displayed is the actual drying time.
time adjust
Q
The Time Adjust feature can be used only with Timed Cycles.
• Press TIMED CYCI.ES TEMP until the desired temperature glows yellow.
high
e regular
medium
S low
air dry
l timed cycles i
temp
Temperature settings can be changed only with Timed Cycles.
• Press the WRINKI.E PREVENT feature button if this option is desired.
• Press the SIGNAl. ON/OFF button to set the end of cycle signal
• Press and hold START/PAUSE button until dryer starts (about 1 second).
NOTES:
Sensor Cycles Dryness is not adjustable for Timed, Steam, or Sanitize Cycles. Pressing
the SENSOR CYCI_E DRYNESS button will cause the triple beep indicating that this
option is not se[ectab[e.
A light next to each feature will glow yellow when the feature is selected. The light
will not glow when the selection is unavailable with the cycle or option combinations
selected.
While a Timed Cycle is running, you can change the settings for Time, Temperature,
the WRINKI.E PREVENT feature and the cycle signals. Press the START/PAUSE button
once to stop the dryer, allowing you to select another cycle.