XTP PI 400 Power Injector • Installation and Operation 5
Rear Panel Connectors
100-240V 1.6 A
50/60 Hz
1
XTP
PWR
XTP PWR
2
XTP
PWR
XTP PWR
3
XTP
PWR
XTP PWR
4
XTP
PWR
XTP PWR
XTP PI 400
Figure 3. Rear Panel Features
ATTENTION: Do not connect these devices to a computer data or telecommunications
network.
NOTE: The XTP PI 400 does not switch XTP signals.
a
AC power connector — Connect the IEC power cord to the AC power connector.
b
XTP connector — Connect an Extron XTP device that is powered by a local power
source to the XTP connector on any of the four port pairs.
c
XTP PWR connector — Connect an Extron XTP device that requires power from an
external source to the XTP PWR connector. Make sure there is an XTP device plugged
into the XTP connector on the same port pair.
NOTE: Do not loop XTP port pairs on a single cable run to remotely power the
transmitter and receiver. Figure 5, below, shows this type of application, which is not
recommended by Extron.
XTP
PWR
XTP PWR
To an XTP Device To an XTP Device
that Requires an
External Power Supply
Figure 4. Correct application
Installation Overview
1. Mount the device in a rack, under a table, or on a tabletop (see Mounting on page 8).
2. Connect a locally powered XTP device
to the XTP connector on one of the port
pairs.
3. On the same port pair, connect an
XTP device that requires power from
an external source to the XTP PWR
connector.
4. Repeat steps 2 and 3 for each XTP port
pair as necessary.
5. Connect AC power to the XTP PI 400.
• Figure 5. Incorrect application
100-240V x.xA
50/60 Hz
1
XTP
PWR
XTP PWR
2
XTP
PWR
XTP PWR
3
XTP
PWR
XTP PWR
4
XTP
PWR
XTP PWR
XTP PI 400
POWER
12V
--A MAX
RxGTx
RS-232 IR
RL
RxTx
-+-+
1
2
AUDIO
ON
AUDIO
RESET
LAN
ACT LINK
OVER XTP
OUTPUTS RELAYS
SIG LINK
XTP IN
HDMI
OFF
S/PDIF
POWER
12V
HDMI
--A MAX
RxGTx
RS-232 IR
RxTx
−+−+
LR
LOOP-THRU
RESET
AUDIO
OFF
ON
AUDIO
LAN
ACT LINK
SIG LINK
XTP OUT
INPUTS
OVER XTP
CATx
CATx
XTP T HDMI
Transmitter
XTP R HDMI
Receiver
CORRECT
XTP PI 400
XTP Power Injector
100-240V x.xA
50/60 Hz
1
XTP
PWR
XTP PWR
2
XTP
PWR
XTP PWR
3
XTP
PWR
XTP PWR
4
XTP
PWR
XTP PWR
XTP PI 400
POWER
12V
--A MAX
RxGTx
RS-232 IR
RL
RxTx
-+-+
1
2
AUDIO
ON
AUDIO
RESET
LAN
ACT LINK
OVER XTP
OUTPUTS RELAYS
SIG LINK
XTP IN
HDMI
OFF
S/PDIF
CATx
XTP R HDMI
Receiver
XTP PI 400
XTP Power Injector
CATx
Remote Power
POWER
12V
HDMI
--A MAX
RxGTx
RS-232 IR
RxTx
−+−+
LR
LOOP-THRU
RESET
AUDIO
OFF
ON
AUDIO
LAN
ACT LINK
SIG LINK
XTP OUT
INPUTS
OVER XTP
CATx
XTP T HDMI
Transmitter
Remote Power
Remote Power
100-240V x.xA
50/60 Hz
1
XTP
PWR
XTP PWR
2
XTP
PWR
XTP PWR
3
XTP
PWR
XTP PWR
4
XTP
PWR
XTP PWR
XTP PI 400
POWER
12V
--A MAX
RxGTx
RS-232 IR
RL
RxTx
-+-+
1
2
AUDIO
ON
AUDIO
RESET
LAN
ACT LINK
OVER XTP
OUTPUTS RELAYS
SIG LINK
XTP IN
HDMI
OFF
S/PDIF
POWER
12V
HDMI
--A MAX
RxGTx
RS-232 IR
RxTx
−+−+
LR
LOOP-THRU
RESET
AUDIO
OFF
ON
AUDIO
LAN
ACT LINK
SIG LINK
XTP OUT
INPUTS
OVER XTP
CATx
CATx
XTP T HDMI
Transmitter
XTP R HDMI
Receiver
CORRECT
INCORRECT
XTP PI 400
XTP Power Injector
100-240V x.xA
50/60 Hz
1
XTP
PWR
XTP PWR
2
XTP
PWR
XTP PWR
3
XTP
PWR
XTP PWR
4
XTP
PWR
XTP PWR
XTP PI 400
POWER
12V
--A MAX
RxGTx
RS-232 IR
RL
RxTx
-+-+
1
2
AUDIO
ON
AUDIO
RESET
LAN
ACT LINK
OVER XTP
OUTPUTS RELAYS
SIG LINK
XTP IN
HDMI
OFF
S/PDIF
CATx
XTP R HDMI
XTP PI 400
XTP Power Injector
CATx
POWER
12V
HDMI
--A MAX
RxGTx
RS-232 IR
RxTx
−+−+
LR
LOOP-THRU
RESET
AUDIO
OFF
ON
AUDIO
LAN
ACT LINK
SIG LINK
XTP OUT
INPUTS
OVER XTP
CATx
XTP T HDMI
Transmitter
Remote Power
Remote Power
