Maintenance Information
Cleaning
Case Exterior
Clean surfaces frequently with warm water and mild
detergent. Do not use strong alkali solutions, steel
wool, or abrasive cleansers.
Non-Glare Glass
Non-glare glass surfaces are coated to reduce the
glare from lighting. Care must be taken not to
scratch the coating. Use the following products only.
Cleaning Cloths
Scotch-Brite High Performance Cloth - manufac-
tured by 3M and available in most grocery stores
under the name Scothch-Brite Microfiber Cleaning
Cloth in a 12" x14" size. This cloth is washable and
may be reused as long as it remains clean.
Spontex Microfibre Cleaning Cloth - distributed
by Spontex and available in most grocery stores
under the same name in a 15.75" x 12" size. This
cloth is washable and may be reused as long as it
remains clean.
The cleaning cloths named above will normally
remove dust, grease, oil and fingerprints without the
need for cleaning fluids. A light spray of the clean-
ing fluids listed below will reduce the time required
for cleaning.
Cleaning Fluid - for more difficult cleaning jobs,
these products are recommended:
Windex - standard product only (extra-strength
or specialty products may not be suitable)
Glass-Plus - standard product only (extra-
strength or specialty products may not be suiable)
Warm Water
DO NOT USE
the following types of materials can
be used for cleaning glass with anti-reflective
coatings.
Coarse Paper Towels
Scouring Pads or Powders
Steel wool or Steel Fiber Materials
Blades
Acidic or highly Alkaline detergents
Fluorine based detergents
Case Interior
All shelving and lower deck can be removed for
cleaning (See installation instructions for removing
and setting shelving). Check to make sure the
case drain(s) are not clogged. Clean interior with
warm water and a mild detergent. A sanitizer
should be used after washing to eliminate bacteria.
Rinse thoroughly being careful not to flood drain
system. Avoid spraying water directly into electrical
connections. DO NOT USE A HIGH PRESSURE
WATER HOSE. MAKE SURE FANS ARE SHUT
OFF WHEN CLEANING THE INTERIOR OF THE
CASE. Drains should be cleaned once a month.
Light Replacement
The fluorescent lights in this case are furnished with
plastic safety shields and end caps. When replac-
ing fluorescent lamps, be certain to reinstall safety
shield and caps. (See illustration). If the bulb is not
fully seated the lights will not operate. BE SURE
BULBS ARE FULLY SEATED.
The light switch is mounted to the right side of the
ceiling. See mechanical drawing for ballast box
location.
down.
plastic safety tube protector.
Insert bulb into end cap.
light fixture.
A.
B.
C.
Load Limits
DO NOT place product in merchandisers until all
refrigeration controls have been adjusted and are at
the proper operating temperature. DO NOT place
product above load limits or in such a way that the
discharge or return air grill are blocked. This will
effect the performance of the case and effect the
defrost system.
Evaporator Coil
Clean as needed.
Condenser Coil
FAILURE TO CLEAN COILS WILL VOID WARRAN-
TY. Clean condenser coil every three months or as
needed with a whisk broom or vacuum. Disconnect
power when servicing. FINS ON CONDENSER
COIL ARE SHARP!
Condensate Heater
(Evap-O-Way)
Add one teaspoon of scale remover or white vine-
gar to condensate heater pan once every three
months or as needed. Heater is designed for 75ยบ
and 50% relative humidity. The condensate pan
may overflow if design limits are exceeded.
Seafood Application
Plexiglas should be removed for cleaning. Reinstall
Plexiglas by placing in front of case. Ice will hold it
in place. PLEXIGLAS MUST BE IN PLACE TO
KEEP ICE OUT OF AIR SCREEN.
