Filter
Top Products
19
Troubleshooting
The following symptoms are not trouble.
Symptoms Causes
Machine begins fi lling water in
the middle of the wash.
• When the laundry amount is large at the HIGH water level, the
machine sometimes fi lls automatically. When level goes down,
the machine fi lls automatically.
The water level is too high for
the amount of laundry being
washed.
• When the laundry is already soaked with water before the
wash is started, or if there is water in the tub before the wash
is started, the water level will sometimes be higher.
The water level is too low for
the amount of laundry being
washed.
• With light laundry made of synthetic or blended fabric, the
water level will sometimes be lower.
Midway during spinning, the
operation suddenly changes
to rinsing.
• When the laundry is unbalanced during spin, rinsing and
automatic correction of unbalanced laundry will begin. Later
spinning will return to normal condition.
Water does not fl ow through
the lint fi lter. Double Cascade
does not operate.
• When the water level is set to very Low, water sometimes will
not fl ow through the lint fi lter. Double Cascade does not oper-
ate when these settings have been selected.
The water is drained even
fi lled by a bucket.
• Do not leave more than 15 seconds while powered on. Fill the
water while powered off or after pushing the start button.
During draining, the laundry
and the spinner rotates with
irregular movements.
• To suppress detergent suds build-up, the washing tub turns
slowly and quickly.
The buttons do not work. • Only the [WATER LEVEL] and [PROCESS] button is available
after the machine begins washing.
• To change the setting, press the [POWER OFF] button and
reconfi gure the setting.
If you start with the rinse
cycle, the tub is not fi lled
with water.
• When there is water in the tub, the operation starts with the
draining.
Washing machine does not
run at all.
• Check if there is power failure.
• Check if the power fuse has blown out or the breaker is
actuated.
• Check if the power plug is plugged in thoroughly.
• Check if the “power switch’’ has been pressed.
• Has the water faucet been turned on?
• Check if the [START/HOLD] button has been pressed.
• Has the machine been programmed under [RESERVE] timer?
Water is not supplied. • Check if the water faucet is turned on.
• Is the water supply cut off?
• Check if the connection of the water supply hose is clogged
with dirt.
• Please refer to page 14 for cleaning water supply hose filter.
Washing operation still
continue even though the
expected finishing time had
passed on Reserve Program.
Washing time will be longer because of laundry unbalance, water
feeding and draining condition.
Buzzer sounds followed by a
draining when opening the lid
during wash and rinse.
In the case when open the lid after setting the [CHILD LOCK]
mode, it will force the draining process. Pull out power plug from
the outlet and replug it after 5 seconds.
Buzzer sounds when opening
the lid during cascade rinsing
or spinning.
This is a reminder for a user not to put a hand and/or any object
into the tub. It is not out of order.
w To turn off the buzzer, close the lid.
Tub shaking with the sound of
water.
This is the sound of the liquid to maintain the balance during
spinning.
Water supply failure. Normally after the water supply failure, the water will become
muddy.
Detach the water feeding hose and turn on the water faucet to
release to due muddy water. Fix water hose and start washing.
Power failure. In this case, [POWER ON] and [START/HOLD] buttons need to
be pressed again after electricity is restored. Then the machine
will resume operation automatically from beginning of the
stopped process.
NA-F62-70B1-ENABPS.indd 19NA-F62-70B1-ENABPS.indd 19 5/8/08 9:16:49 AM5/8/08 9:16:49 AM