Filter
Top Products
10
Pricing
After the door is opened following the completion of a cycle, the
display indicates the cycle price (unless set for free operation). As
coins are dropped or debit inputs arrive, the display will change
to lead the user through the initiation of a cycle.
Free Cycles
This is established by setting the cycle price to zero. When this
ha
ppens, “SELECT CYCLE” will appear rather than a cycle price.
Display
After the washer has been installed
and plugged in, the display
will show “0 MINUTES.” Once the washer has
been plugged in
and the washer door opened and closed, the display will show
the price. In washers set for free cycles, the display will flash
“SELECT CYCLE.”
NOTE: Not displayed on washer as shown. Message scrolls
followed by the failure code.
Control Set-up Procedures
IMPORTANT: Read all instructions before operating.
■ PD Models: Insert access door key, turn, and lift to remove
access door.
■ PN Models: Remove connector AA1 on the circuit board.
Set-up procedures can be entered by
using the Service Access
Code for PN washers without a key switch installed.
IMPORTANT: Unplug wa
sher or disconnect power before
opening the console. To access connector AA1:
Unplug
washer or disconnect power.
Open con
sole, disconnect plug on AA1, close console.
Plu
g in washer or reconnect power.
The washer is now in the set-up mod
e. The lower fabric setting
key pads and the digital display are used to set up the controls.
The display can contain 4 numbers and/or letters and a decimal
point. These are used to indicate the set-up codes and related
code values available for use in programming the washer.
Once the washer has been programmed with a hand held
device
using Accu Trac, or a Gen. 2 card reader has been installed, the
washer will be put into dAS mode permanently, and dAS will be
displayed every time set-up mode is accessed.
How to use the key pads to program controls
1. The PERMANENT PRESS key pad is used to adjust the
values associated with set-up codes. Pr
essing this key pad
will change the value by incr
ements. Rapid adjustment
is possible by holding the key pad down.
2. The WOOLENS key
pad advances you through the set-up
codes. Pressing this key pad will advance you to the next
available set-up code. Holding the key pad down will
automatically advance through the set-up codes at a rate
of 1 per second.
3. The
DELICATES & KNITS key pad is used to select or
deselect options.
Start Operating Set-up
NOTE: Prior operation, a payment system or an OPL kit must be
installed.
Before proceeding, it is worth noting that, despite all of the
options ava
ilable, an owner can simply choose to un-crate a new
commercial washer, hook it up, plug it in, and have a washer that
operates. Washers are preset at the factory for a 14-minute wash
period and 3 rinses (no extra rinse).
Set-up Codes
■ The WOOLENS key pad will advance you from code to code.
■ The PERMANENT PRESS key pad will change the code
value.
■ The DELICATES & KNITS key pad will select or deselect
options.
FOR PN MODELS: The set-up codes are the same as for the
“PD” model except where noted.
The set-up code is indicated b
y the one or two left-hand
characters. The set-up code value is indicated by the two or
three right-hand characters.
CODE EXPLANATION
6 07 REGULAR CYCLE PRICE (Factory Default)
6
6
07
00
Represents the number of coins (Coin 1) needed to
start the
washer; may adjust from 0-39. (See
VALUE OF COIN 1.) Advance from 0-39 by
pressing PERMANENT PRESS key pad. Factory
default of 7 x coin 1.
PN MODELS ONLY: Factory default for 0 coins.
With coin slide activation, this represents the
n
umber of push-in actuations of a coin slide to start
the washer.
6 01 setting would represent one coin slide
ac
tuation.
NOTE:
For coin slide activation, replacement of the
meter case is necessary.
Press the WOOLENS key pad onc
e to advance to
next code.
7 14 WASH LENGTH
7 14
This is the number of minutes for WASH. Washer
c
omes from the factory preset with 14 minutes.
Choose fr
om 9-17 minutes by pressing the
PERMAN
ENT PRESS key pad.
Press the WOOLENS key pad once to advance
to next code.