Kenmore 110.2807 Washer User Manual


 
7,
Press START. The countdown to the wash cycle will show in
the time display window, and the Delay Start indicator light
will begin to flash.
NOTE: The Start indicator light will not flash when Delay Start
is chosen. You must press Start to initiate a countdown for
the cycle to begin.
To change the Delay Start time:
Press STOR
Press DELAY START to select the desired delay time.
Press START to begin the countdown.
To cancel Delay Start:
Press START again to begin the cycle right away, or press
STOP twice to cancel the cycle.
Use these pads to select the desired options for your wash
cycle..
OPTIONS
_Cycle Signal
_ Fabric Softener
_ Stain Treat
Prewash
_ 2nd Rinse
Auto Soak
Cycle Signal
The End of Cycle Signal produces an audible sound when the
wash cycle is finished. This signal is helpful when you are
removing items from the washer as soon as it stops. The End of
Cycle Signal is on when option is lit.
Stain Treat/Prewash
This option provides enhanced cleaning action for tough
stains. The Heavy Duty cycle automatically includes Stain
Treat. Choosing Stain Treat will add approximately 5 minutes
to a cycle. Stain Treat should be started on a dry load only
and should not be selected after the tub has started filling
with water. Stain Treat may be selected as an option on all
other cycles.
When Prewash is selected, the washer fills to the desired
water level. It then alternates between 1 minute of wash
action and a 1-minute pause period three consecutive times
with an extended pause to end the cycle. When Prewash is
complete, the washer advances to the selected wash cycle.
The Prewash option extends your wash time by
approximately 11 minutes.
2nd Rinse/Auto Soak
Press the option button for 2nd Rinse/Auto Soak until your
desired choice is highlighted.
2nd Rinse can be selected to aid in the removal of
detergent or bleach residue from garments. This option
provides an additional rinse with the same water
temperature as the first rinse. This is the default rinse
setting for the Whitest White cycle. Fabric softener will be
dispensed in the 2nd rinse.
When Auto Soak is selected, the washer saturates the
load with water and detergent then pauses to allow the
detergent to work on soils. The pause is followed by a
slow-speed spin. The washer pauses and spins six times
before advancing to the desired wash cycle. Auto Soak
adds approximately 12 minutes to the wash cycle.
Fabric Softener
The Fabric Softener option must be selected if liquid fabric
softener is added to the fabric softener dispenser, unless a 2nd
Rinse is selected. This option flushes the dispenser at the right
time in a deep water rinse for optional distribution. This option
may also be selected if a spray rinse is not desired.
Power
Press POWER to turn the washer on or off.
Power
@
Start
Press START to start your washer after a cycle has been
selected. Be sure all desired Modifiers and Options have been
selected. The lid must be closed for the washer to start.
IMPORTANT: Water will be dispensed in the washer for a
moment, the lid will unlock, lock again, and then the cycle will
continue. This is normal.
Stop
Press STOP once to pause or stop the washer at any time. Press
START to continue the cycle. Press STOP twice to turn off the
washer. Press STOP once to unlock the lid and add a garment.
s,>_oUNto@
No;,ms Sounds
Your new washer may make sounds your old one didn't. Because
the sounds might be unfamiliar, you may be concerned about
them. These sounds may be normal.
During washing
If you select the Stain Treat option, you will hear a spin/spray
noise at the start of the cycle.
During drain
If water is drained quickly from your washer (depending on your
installation), you may hear air being pulled through the pump
during the end of draining.
During wash and spin
This washer does not have a transmission. The motor provides
direct drive for wash and spin. You will hear sounds that are
different from those of a conventional washer.
16