Filter
Top Products
The digitron displays E0.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
The water filling does not work, or is
slow. After about 40 minutes later,
the digital displays E4.
The drainage cannot work, or is too slow.
The digitron displays E1.
It stops running in midway. The digitron
displays E2.
The top lid is not closed.
The top lid is opened during reserve
procedure.
Close the top lid.
Close the top lid.
Is the drain hose put down?
Is the drain hose blocked?
Put down the drain hose. Open and close the
top lid once.
Clean the foreign material. Open and close
the top Lid Once.
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.
The machine will start running after 10
seconds of being placed horizontally.
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
Open the water tap. Push the Start/Pause
button once.
Clean the water inlet valve then push
the Start/Pause button once.
Push the Start/Pause button once.
The water level sensor is bad.
Please contact the after-sales service department.
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
Is the screw of the jointer of water
inlet hose loose or awry?
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Fasten the screw of the jointer properly.
The water tap leaks
The digitron displays E6.
There's abnormal sound
inside the machine
Phenomenan The reason How to settle
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
The machine does
not act
Not wash
Not spin
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
The temperature sensor is fallen.
The water level drops to the replacement
point after it has supplied water for 2 times
during the whole process.
Open and close the top lid once.
The digitron displays E5.
The digitron displays F5.
Please contact the after-sales service department.
* The actual heating temperature may have
discrepancy with the setting level.
* This is the normal phenomenon .The actual heating
temperature is also influenced by the atmosphere
temperature the water temperature for wash and the
water hardness.
When the power plug is inserted,computer
board indicator is switched on,and the machine
starts working.
*
*
Explanation
* The spinning is intermittent when it starts.
* The wash procedure pauses.
* Select "SPIN" program, but it does not work.
* The pusaltor pauses during washing , rinsing or
adding water.
* There may be some water flowing out of the
drain hose in the first use of the machine.
* Balance the laundries to avoid slanting.
* The cloth sensor is detecting the cloth. It will start
adding water after about 48 seconds.
* The program is setting the drain time. A certain
period is needed before it starts spinning.
* It is to avoid splashing during water filling.
* It is the water remained in the performance
inspection by the factory.
It is the special resume function.
.
In the case of power
failure or the power plug is loose during washing, the
machine can save the running program, and resume
the program after the power supply is recobered. You
do not need to set the program again
Common phenomena
Phenomena