Haier HWM78-0528T Washer/Dryer User Manual


 
2
Safety precautions
Back
Front
The ventilation
holes at the bottom
Soft object
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Do not use water hotter than 50 .
In case the washing machine is installed on ground
with carpet, do not block the ventilation hole with
carpet.
Trouble-shooting answer to question
The water level sensor is bad.
Please contact the after-sales
service department.
The digitron displays E6.
Phenomena The reason How to settle
Thetop lid is not closed
Is thedrain hose put down?
Is thedrain hose blockedby
foreignmaterial?
Arethe laundries put slantingly?
Arethe laundries slanting in
spinning?
Is themachine slanting?
Is themachine slanting?
Thewatertap is not open
Thewaterinlet valve is blocked
The water pressure is too low
and the current is too small
Is therepower failure?
Is thepower plug loose?
Is thejointer screw of the water
inlet hose is looseor twisted
awry?
Thewaterfaucet leaks
There's abnormal soundinside the
machine
Themachine does
not act
Close the top lid
Put downthe drain hose. Open
andclose thetop lid once.
Cleanthe foreign material.
Open andclose the top lid once.
Re-orderthe laundries. Close the
top lid.Level the machine in right
position.
Open and close the top lid once.
Open the water tap.
Push the "Start/Pause" button.
Clean the water inlet valve.
Push the "Start/Pause" button.
Wait for the normal water pressure
Before use.
Useitwhen thepower is on.
Insert the power plug tightly.
Level the machine properly.
Re-order thelaundries.
Fastenthe jointer screw
properly.
Does thewater level arrive at the
set water level?
Affusion to theset water level.
Is thepower plug loose?
Insert the power plug tightly.
Is thetop lid closed?
Close the top lid
Arethe laundries put orderly?
Put the laundries orderly.
Not spin
Not wash
Buzzing upon reservation starts,
the digitron displays "E0"
Safety switch actuates, not
spin,(after self-correction
twice),
the digitron displays
"E3",
buzzing
No orslow water filling (not
reaching the levelin 30 min),
the digitron displays
"E4",
buzzing
No orslow drain,
the digitron
displays
"E1"
,buzzing.
If the nozzle is choked with
foreign bodies
Remove the foreign bodies
Poor orno waterfall flow
The top coverleaves open
Close the top lid
Running pauses during spin,
the digitron displays
"E2",
buzzing
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained performance inspection
by the factory.
Common phenomena
Phenomena
Explanation
The spinning is intermittent when it starts.
The wash procedure pauses.
Select spin program, but it does not work.
Balance the laundries to avoid slanting.
The cloth sensor is detecting , it will add water
after about 48 senconds.
The program is setting the drain time , certain
period is needed before it starts spinning.
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not
breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.
Earth
Pleaseplug thepowerplug onspecial
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or our customer care agent.
The washing machine must be positioned so that
the plug is accessible. Be sure to pull the plug off
and close the water faucet in following cases:
power failure, delivering the machine, setting the
machine idle or cleaning the machine. Do not plug
or pull the power plug with wet hand.