Beko WMB 71031 PTM Washer/Dryer User Manual


  Open as PDF
of 54
 
13
EN
Starting the programme
Press Start / Pause button to start the programme.
Programmefollow-uplightshowingthestartupof
the programme will turn on.
C
Ifnoprogrammeisstartedornokeyis
pressed within 1 minute during programme
selection process, the machine will switch
to Pause mode and the illumination level of
the temperature, speed and loading door
indicatorlightswilldecrease.Otherindicator
lightsandindicatorswillturnoff.Oncethe
Programme Selection knob is rotated or
any button is pressed, indicator lights and
indicators will turn on again.
Child Lock
UseChildLockfunctiontopreventchildrenfrom
tampering with the machine. Thus you can avoid
any changes in a running programme.
C
IftheProgrammeSelectionknobisturned
when the Child Lock is active, "Con" appears
on the display. The Child Lock does not
allow any change in the programmes and the
selected temperature, speed and auxiliary
functions.
C
Even if another programme is selected with
the Programme Selection knob while the Child
Lock is active, previously selected programme
will continue running.
To activate the Child Lock:
Press and hold 1
st
and 2
nd
Auxiliary Function
buttons for 3 seconds. The lights on the 1
st
and
2
nd
Auxiliary Function buttons will flash, and
"C03","C02","C01"willappearonthedisplay
respectively while you keep the buttons pressed
for 3 seconds. Then, "Con" will appear on the
display indicating that the Child Lock is activated.
IfyoupressanybuttonorturntheProgramme
Selection knob when the Child Lock is active,
same phrase will appear on the display. The lights
on the 1st and 2nd auxiliary function buttons that
are used to deactivate the Child Lock will blink 3
times.
To deactivate the Child Lock:
Press and hold 1
st
and 2
nd
auxiliary function
buttons for 3 seconds while any programme is
running. The lights on the 1
st
and 2
nd
Auxiliary
Functionbuttonswillflash,and"C03","C02",
"C01"willappearonthedisplayrespectivelywhile
you keep the buttons pressed for 3 seconds.
Then,"COFF"willappearonthedisplayindicating
that the Child Lock is deactivated.
C
Inadditiontothemethodabove,todeactivate
the Child Lock, switch the Programme
SelectionknobtoOn/Offpositionwhenno
programme is running, and select another
programme.
C
Child Lock is not deactivated after power
failures or when the machine is unplugged.
Progress of programme
Progress of a running programme can be followed
fromtheProgrammeFollow-upindicator.At
the beginning of every programme step, the
relevant indicator light will turn on and light of the
completed step will turn off.
You can change the auxiliary functions, speed
and temperature settings without stopping the
programme flow while the programme is running.
To do this, the change you are going to make must
beinastepaftertherunningprogrammestep.If
the change is not compatible, relevant lights will
flash for 3 times.
C
Ifthemachinedoesnotpasstothespinning
step,RinseHoldfunctionmightbeactive
or the automatic unbalanced load detection
system might be activated due to the
unbalanced distribution of the laundry in the
machine.
Loading door lock
There is a locking system on the loading door of
the machine that prevents opening of the door in
cases when the water level is unsuitable.
Loading door light will start flashing when the
machine is switched to Pause mode. Machine
checksthelevelofthewaterinside.Ifthelevelis
suitable,LoadingDoorlightilluminatessteadily
within1-2minutesandtheloadingdoorcanbe
opened.
Ifthelevelisunsuitable,LoadingDoorlightturns
offandtheloadingdoorcannotbeopened.If
youareobligedtoopentheLoadingDoorwhile
theLoadingDoorlightisoff,youhavetocancel
the current programme; see "Canceling the
programme".
Changing the selections after
programme has started
Switching the machine to pause mode
Press the Start / Pause button to switch the
machine to pause mode while a programme is
running. The light of the step which the machine
isinstartsflashingintheProgrammeFollow-up
indicator to show that the machine has been
switched to the pause mode.
Also, when the loading door is ready to be opened,
LoadingDoorlightwillalsoilluminatecontinuously
in addition to the programme step light.
Changing the speed and temperature settings
for auxiliary functions
Dependingonthesteptheprogrammehas
reached, you may cancel or activate the auxiliary
functions; see, "Auxiliary function selection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
C
Ifnochangeisallowed,therelevantlightwill
flash for 3 times.
Adding or taking out laundry
Press the Start / Pause button to switch the
machinetopausemode.Theprogrammefollow-
 previous next