Filter
Top Products
Page 21
ENGLISH
ENGLISH
TRTROUBLESHOOOUBLESHOOTINGTING
(CONTINUED) (CONTINUED)
The door won’t open.The door won’t open.
♦ Make sure the power to the unit is on. If the power
is on and the indicator lamp is not lit, there is no
power supply. Check that the machine is properly
plugged into the electrical outlet. If it is, the fuses
may be blown. Call a service technician.
♦ Make sure all the water has drained out.
♦ If there is no water in the machine and the door
won’t open in the normal manner, you should be
able to open it manually, as follows:
1. Make sure the tub is as empty as possible and
the power is turned off.
2. Using the flat edge of the liquid detergent
partition piece, a flathead screwdriver or similar
item, gently pry open the drain pump cover.
3. Using a T20 or flathead screwdriver, unscrew
the red plastic looped handle.
4. Pull the handle toward you. The door should
open.
The machine won’t start.The machine won’t start.
♦ Check that the glass door is closed securely.
♦ Make sure the power switch is turned on.
♦ If the power switch is on and the indicator lamp is not
lit, there is no power supply. Make sure the machine
is properly plugged into the electrical outlet.
♦ Check the house breaker switch/fuses.
The machine doesn’t fill.The machine doesn’t fill.
♦ Make sure the tap to the water supply line is open.
♦ Turn off the water supply then disconnect the inlet
hose and check to see if the strainer in the inlet
connection is blocked.
The machine will not spin.The machine will not spin.
♦ Make sure the pin trap or outlet hose isn’t blocked.
Clean if necessary. (See page 18.)
♦ Make sure the No Spin option is turned off.
♦ If a load is out of balance, the washer will rotate a
few seconds to redistribute the load then attempt to
spin again. It will do this up to ten times at a high
spin speed (1000 rpm or higher). If it still isn’t
balanced, it will advance the timer with no spin.
Extreme vibration during spinExtreme vibration during spin
cycle.cycle.
♦ Make sure the packaging and shipping supports
were removed properly. (See page 4.)
♦ Check that the machine is level.
♦ Adjust machine feet and tighten locknuts. (See page 4.)
Oversudsing.Oversudsing.
♦ Too much detergent could cause suds to backup
through the detergent compartment and run down
the front of the washer onto the floor. The suds will
condensate into water and form a small puddle on the
floor. (See page 8 for detergent recommendations.)
Washer stops during cycle.Washer stops during cycle.
♦ It is normal for the machine to pause occasionally
during operation, especially between cycles and
during the delicate wash program.
♦ Make sure the No Spin option isn’t turned on.
♦ If the power switch is on and the indicator lamp is
not lit, there is no power supply. Make sure the
machine is properly plugged into the electrical outlet.
♦ Check the house breaker switch/fuses.
Foam in the final rinse water.Foam in the final rinse water.
♦ Make sure nothing is blocking the outlet hose.
♦ Check for kinks in the outlet hose.
♦ Make sure the pin trap isn’t blocked. (See page 18.)
♦ Make sure that no part of the hose (including any
joints) is less than 3/4” (19 mm) in diameter.
Water left in the machine afterWater left in the machine after
final spin.final spin.
♦ Make sure the No Spin option isn’t turned on.
♦ Make sure the pin trap isn’t clogged. (See page 18.)
♦ Make sure the outlet hose isn’t clogged.
♦Check for kinks in the outlet hose.
♦ Make sure that no part of the outlet hose (including
any joints) is less than 3/4” (19 mm) in diameter.
Water leaks.Water leaks.
♦ All hoses should be inspected at least once a year.
If they show signs of cracking, they should be
replaced.
♦ Check to see if hose connections at faucets are
tight.
♦ Make sure the end of the outlet hose is securely
inserted into the drain receptacle.
♦ Make sure nothing is caught between the Smart Seal
and the tank, such as apron strings, small
handkerchiefs, socks, etc.
Emergency
Door Handle