Asko W6641 W661 Washer/Dryer User Manual


 
Page 13
ENGLISH
ENGLISH
You can make temporary changes to the wash
temperature and/or spin speed on the preset
programs. Simply press the button for the preset
program you want to use then follow the instructions at
right. The settings will revert to normal at the end of the
program.
MAKING TEMPORARY PROGRAM CHANGES
CUSTOMIZING THE PRESET PROGRAM BUTTONS
ASKO washers are delivered preset with four commonly
used programs. The table below lists the preset
programs and the settings for each. To select a
program, simply press one of the program buttons and
press Start. For additional programming options, refer
THE PRESET PROGRAMS THE PRESET PROGRAMS
P 1 P 2 P3 P4
ASKO’s EasyControl™ panel makes it simple to
customize the preset programs to perfectly fit your
laundry needs. You needn’t worry about making an error
because you can easily restore the original program
settings.
In addition to the preset programs listed above, you
can customize the preset buttons to use any of the
programs listed in the table below.
Preset Wash Spin # of #
Program Wash Cycle Types of Laundry Temp
(1)
Speed
(1)(2)(3)
Rinses Spins
P1 Light wash Normally soiled loads 140° F 1600 rpm 5 3
P2 Light wash Normally soiled perm press 105° F 1600 rpm 5 3
P3 Quick wash Lightly soiled fabrics 105° F 1600 rpm 3 1
P4 Hand wash Washable silks, nylon, etc. 85° F 800 rpm 3 1
NOTES:
(1) You can temporarily adjust the temperature and spin speed settings. (See “Making Temporary Program
Changes” below.)
(2) The spin speeds in the preset programs are the maximum speed settings for these specific wash
programs.
(3) Model W6641 has a maximum spin speed of 1400 rpm.
WARNING!
Some fabrics may not be able to withstand extremely hot temperatures.
Please refer to the “Recommended Wash Temperatures” section on page 6.
to “Customizing the Preset Program Buttons” below.
Remember, you can temporarily adjust the temperature
setting and spin speed for a preset program. (See
“Making Temporary Program Changes” below.)
AVAILABLE PROGRAMS
Temperature – Press
until the desired temperature
displays in the LCD window. (The options are 85°, 105°,
120°, 140°, 160°, 175°, and 205°.) If you also want to
change the spin speed, read the following paragraph;
otherwise, press Start.
Spin Speed – Press until the desired spin speed
displays in the LCD window then press Start. (The spin
speeds advance in 200 rpm increments.)
This table also lists the pre-programmed settings for
each program. For example, if you select Perma Press
on the program menu, it is automatically programmed
to wash at 105° F using a normal wash action, rinse
three times then do a short spin, then rinse two more
times, do a long spin and drain. You can modify some
of these settings (see “Wash Program Options” on page
14).
NOTE: (1) Model W6641 has a maximum spin speed of 1400 rpm.
PRESET PROGRAMS
Program
Pre-
wash
Main
Wash
Wash
Action
Temp.
(° F)
#
Rinses
Int.
Spin
Final
Spin
Spin
Speed
(1)
Load
Size
Heavy wash yes Long Normal 140 5 2 Long 1600 Full
Normal wash no Long Normal 140 5 2 Long 1600 Full
Light wash no Short Normal 140 5 2 Long 1600 Full
Synthetic wash no Short Normal 105 3 no Short 800 Half
Quick wash no Short Normal 105 3 no Long 1600 Full
Super quick wash no Short Normal 105 2 no Short 800 Half
Wool wash no Short Gentle 85 3 no Short 800 Third
Hand wash no Short Gentle 85 3 no Short 800 Third
Rinse n/a n/a n/a n/a 1 n/a Long 1600 Full
Spin n/a n/a n/a n/a n/a n/a Long 1600 Full
Drain n/a n/a n/a n/a n/a n/a n/a n/a Full