K-31
E6581301
11
[29] Communication function [2/4] Sensorless vector/vector with sensor (Ɣ:Effective, -:Ineffective)
Title
Communi
cation
No.
Function Adjustment range
setting unit
(Panel/Communi
cation)
Default
setting
running
PM
control
V/f Constant
Reference
Speed
control
Torque
control
H
0808
Communication1 time-out
condition selection
1:When communication mode enable
2:1+Driving operation
1/1 0 Enabled Ɣ/Ɣ Ɣ/Ɣ Ɣ Ɣ *1
H
0810 Frequency point selection
1:2-wire RS485
2:4-wire RS485
3:Communication add option
1/1 0 Enabled Ɣ/Ɣ - Ɣ Ɣ 6. 39. 1
H
H
HJ
H
H
HJ
H
0815
Address monitor
(Modbus plus)
1~64 1/1 1 *5
Ɣ/Ɣ Ɣ/Ɣ Ɣ Ɣ *3
H
0816
Command selection
(Modbus plus)
0: Prohibit
1: Permit
1/1 0 Enabled
Ɣ/Ɣ Ɣ/Ɣ Ɣ Ɣ *3
H
0817
Number of command
(Modbus plus)
0~8 1/1 0 Enabled Ɣ/Ɣ Ɣ/Ɣ Ɣ Ɣ *3
H
0818
Number of monitors
(Modbus plus)
0~8 1/1 0 Enabled Ɣ/Ɣ Ɣ/Ɣ Ɣ Ɣ *3
H
0819
Command station
(Modbus plus)
0~64 1/1 0 Enabled Ɣ/Ɣ Ɣ/Ɣ Ɣ Ɣ *3
H
0820
Communication speed
(4-wire RS485)
1:19200 bps
1/1 1 Enabled Ɣ/Ɣ Ɣ/Ɣ Ɣ Ɣ 6. 39. 1
H
0821
Baud rate
(Ethernet)
1:10Mbps Full
2:10Mbps Half
3:100Mbps Full
1/1 0 Enabled Ɣ/Ɣ Ɣ/Ɣ Ɣ Ɣ *4
H
0822
BDXGrate monitor right port
(Ethernet)
1:10Mbps Full
2:10Mbps Half
3:100Mbps Full
1/1 - *5 Ɣ/Ɣ Ɣ/Ɣ Ɣ Ɣ *4
H
0823
Baud rate monitor left port
(Ethernet)
1:10 Mbps Full
2:10Mbps Half
3:100Mbps Full
1/1 - *5 Ɣ/Ɣ Ɣ/Ɣ Ɣ Ɣ *4
H
0824 (Reservation)
1:-
2:-
1/1 0 Enabled Ɣ/Ɣ Ɣ/Ɣ Ɣ Ɣ *4
*1: For details, refer to Instruction Manual (E6581315) specified in Section 6.42. *2: Effective when a command value is sent by communication.
*3: This function is for Modbus plus communication option (planning). *4: This function is for Etherenet communication option (planning).
*5: This parameter is read only.
