Splendide WDC1025M Washer/Dryer User Manual


 
WINTERIZING
Turn off the hot and cold water source to machine.
Set machine to fill in regular cycle on warm wash.
Turn machine on for a fe
w minutes so machine can
take on any water.
Lift inlet hoses to assure no water is left in inlet hoses.
Turn unit off.
Advanc
e the wash timer to spin cycle and turn on.
This will activate the water pump and will evacuate as
much water as possible.
Turn unit to off.
Place a towel under the drain filter area and remove
drain filter. This will drain any water left in the bottom
of unit.
Install drain filter correctly to assure it does not leak
water.
In extreme conditions you may wish to completely
remove the inlet hoses.
Complete
Page 14
Washer Does Not Start
Washer may not be plugged in or connection may be
loose.
House fuse blown or circuit breaker tripped.
T
imer knob not in correct position.
Cycle selector knob not in correct position.
Door is not securely shut.
Washer Stops During
Cycle
Drain hose is kinked or clogged (Fig. 1).
House fuse blown, circuit breaker tripped, or wall plug
not firmly in receptacle.
No more than 6" of the drain hose should insert into a
standpipe.
The outlet end of the drain hose
must be at least
20" (50 cm) above the base of the machine.
Assure an air break is available to prevent the machine
from siphoning in a standpipe.
The standpipe should be at 25" (62 cm) minimum
34" (86 cm) maximum height.
Assure the drain lo
op or suitable clamp to support drain
hose has been used.
Water Does Not Enter The Washer, Or It Enters
Slowly
Water supply is
not adequate in the area.
Hot and cold water faucets for the inlet hoses are not
turned completely on.
Water is being used els
ewhere in the house, when the
washer is running.
Water inlet hose filter are clogged (Fig. 3).
Water inlet hoses are kinked.
Wash And Rinse Water Temperatures Are Incorrect
The hot water hose and cold water hose are connected
to the wrong faucets.
Water
Is Entering Washer But Tub Does Not Fill
Standpipe for the drain hose is not the correct height.
(Fig. 2), drain hose is to far into standpipe or air break
does not exist.
Water Leaks
Hose connections at faucet and/or machi
ne not tight.
Rubber washers are not inside the metal hose conne
c-
tors (Fig. 3).
Drain hose not securely fastened (Fig. 1,2). Drain pipes
in the house are clogged.
Too much detergent or a high
sudsing detergent in soft
water is being used.
Soil may be on the door seal or gasket of the washer
preventing a tight seal.
Water In Washer Does Not Drain Or Drains Slowly
Drain hose is kinked or clogged (Fig. 1).
Standpipe
does not have a large enough diameter and is
slowing the draining process.
Machine is over soaped.
Wash filter plugged.
Over S
udsing
Too much detergent used.
Detergent used is not compatible with water conditions.
Garments were pretreated, before wash
ing.
Additional laundry aids such as oxygen bleach may
cause additional sudsing.
AV O I D
-
SERVICE CHECK LIST
You may save the cost and inconvenience of an unnecessary service call by first reviewing this easy
-
to
-
use check list
of the most frequently encountered situations that are not the result of defective workmanship or materials.
You
will be charged for a service call while the appliance is in warranty if the problem is not caused by
defective workma
nship or materials.
Review this
Avoid
-
Service Check List
before calling for service. It may save time and expense.