Filter
Top Products
MSOP0922AE/9805AV
ÈPRESS SAFETY FOR INSTALLATION AND SERVICE
ÊGeneral Safety Requirements
(specific warnings, next page and throughout manual)
Incorrect installation, neglected preventive maintenance, abuse, and/or improper repairs or changes to
the machine can cause unsafe operation and personal injuries, such as multiple fractures, amputations, or
death. The owner or his selected representative (owner/user) is responsible for understanding and ensuring
the proper operation and maintenance of the machine. The owner/user must familiarize himself with the
contents of all machine instruction manuals. The owner/user should direct any questions about these instruc-
tions to a Milnor
®
dealer or the Milnor
®
Service department. Most regulatory authorities (including OSHA
in the USA) hold the owner/user ultimately responsible for maintaining a safe working environment. There-
fore, the owner/user must do the following:
• recognize all foreseeable safety hazards within his facility and take actions to protect his personnel,
equipment, and facility
• require that personnel are familiar with all functional and safety aspects of the machine
• ensure safety devices installed on the machine are in place and properly maintained
• ensure all machine parts and assemblies are properly maintained.
ËLaundry Facility
—Provide a supporting floor that is strong and rigid enough to support--with a rea-
sonable safety factor and without undue or objectionable deflection--the weight of the fully loaded machine
and the forces transmitted by it during operation. (For washer-extractors, see “ABOUT THE FORCES
TRANSMITTED BY MILNOR
®
WASHER-EXTRACTORS.”) Provide sufficient clearance for machine
movement. Provide any safety guards, fences, restraints, devices, and verbal and/or posted restrictions nec-
essary to prevent personnel, machines, or other moving machinery from accessing the machine or its path.
Provide adequate ventilation to carry away heat and vapors. Ensure service connections to installed ma-
chines meet local and national safety standards, especially regarding the electrical disconnect (see the Na-
tional Electric Code). Prominently post safety information, including signs showing the source of electrical
disconnect.
COLLISION, CRUSHING, AND PINCH HAZARDS—Serious bodily injury or
death can result to personnel in proximity to machinery/systems that
traverse, elevate, extend, pivot, and/or tilt. The following mandatory mini-
mum safety requirements must be installed with the machinery system:
☞ Safety fence inclosing machine movement areas,
☞ Lockable electric interlocks on all gates, properly interfaced as shown on ma-
chine schematics, to disable machine movement when any gate is opened,
☞ Signs to alert personnel to these hazards, placed prominently around the fenced
area.
☞ Local codes may require additional precautions.
ËPersonnel
—Inform personnel about hazard avoidance and the importance of care and common sense.
Provide personnel with the safety and operating instructions that apply to them. Verify that personnel use
proper safety and operating procedures. Verify that that personnel understand and abide by point-of-hazard
tags on the machine and procedure-specific precautions in the instruction manuals.
ËSafety Devices
—Ensure that no one eliminates or disables any safety device on the machine or in the
facility. Do not allow machine to be used with any missing guard or cover. Service any failing or malfunc-
tioning device before operating the machine.
ËMaintenance
—Ensure the machine is inspected and serviced in accordance with the norms of good
practice and with the preventive maintenance schedule. Replace belts, pulleys, brake shoes/disks, clutch
plates/tires, rollers, seals, alignment guides, etc. before they are severely worn. Immediately investigate any
evidence of impending failure and make needed repairs (e.g., cylinder, shell, or frame cracks; drive compo-
nents such as motors, gear boxes, bearings, etc., whining, grinding, smoking, or becoming abnormally hot;
bending or cracking of cylinder, shell, frame, etc.; leaking seals, hoses, valves, etc.) Do not permit service
or maintenance by unqualified personnel.
ÊDanger From a Descending Press Main Bell
CRUSH HAZARD—Descending main bell will crush anyone under it. Bell
can descend even with power off.
☞ NEVER crawl or reach under the press main bell.
☞ Lock OFF and tag out power and secure factory-supplied safety supports in place
before crawling or reaching under the bell to perform service or maintenance.
☞ ALWAYS ensure all personnel are clear of the press and receiving conveyor be-
fore returning power to either machine for service or maintenance.
ÊDanger From Exposed Electrical Components
SHOCK HAZARD—Contact with high voltage inside electrical boxes or
from other exposed electrical components can kill or seriously injure
you.
☞ Lock OFF and tag out power at wall disconnect before opening any
electrical control boxes.
☞ ALWAYS employ the services of a licensed, qualified electrician when trou-
bleshooting the electrical system.
5