Filter
Top Products
4
2
3
CONTROL PANEL AND FEATURES
WASH CYCLE KNOB
Use the Wash Cycle knob to select cycles on your washer.
Knob does not advance during the progress of the cycle, see
cycle status lights for each stage of the process. See “Cycle
Guide” for detailed descriptions of cycles.
WASH TEMP
Wash Temp senses and maintains uniform water
temperatures by regulating incoming hot and cold water.
Select a wash temperature based on the type of fabric and soils
being washed. For best results and following the garment label
instructions, use the warmest wash water safe for your fabric.
■ On some models and cycles, warm and hot water may be
cooler than your previous washer.
■ Even in a cold and cool water wash, some warm water may
be added to the washer to maintain a minimum temperature.
START/PAUSE BUTTON
Press to start the selected cycle; press again to pause the
cycle and unlock the lid.
NOTE: If the washer is spinning, it may take several minutes to
unlock the lid. Press and hold for 3 seconds to cancel a cycle
and the washer will drain.
CYCLE STATUS LIGHTS
The Cycle Status Lights show the progress of a cycle. At each
stage of the process, you may notice sounds or
pauses that are different from traditional washers.
SENSING
Once you close the lid and start a cycle, the washer will
begin filling with the initial amount of water. This will take
approximately 2-3 minutes and the lid will be unlocked at this
time. Then the lid must be closed.
If the lid is open when the water stops entering the washer,
the cycle will not continue until the lid has been closed
and the START/Pause button is pressed. If the cycle has
not been continued within 10 minutes of the water filling
the washer, the washer will pump out the water. If the lid is
closed, it will then lock and the sensing process begins and
additional water will be added, if required. You will hear the
motor turn the basket in short pulses to thoroughly wet the
load.
1
2
3
4
WASH
You will hear the motor and agitator moving the load. During
the first stage of the sensing/wash cycle, water will partially
fill the washer and then begin to move the load. It is normal
to have the sensing light on during this stage. You will hear
the agitator rotate, followed by a several second pause. This
process will repeat for several minutes, allowing the entire
load to become saturated. The lower water level combined
with HE detergent at this stage allows for concentrated
cleaning. Concentrated cleaning delivers the detergent
directly to the soils. It is normal for the load to be above the
water line during this stage. At the beginning of the second
stage, the washer will add water to the correct level based
on the load size. You will hear the agitator move quicker
during this stage of the wash cycle. The motor sounds may
change at different stages in the wash cycle.
RINSE
You will hear sounds similar to the wash cycle as the washer
rinses and moves the load. For cycles that use the Extra
Rinse option, you will hear sounds similar to the wash cycle
as the washers rinses and moves the load.
SPIN
The washer spins the load at increasing speeds for
proper water removal, based on the selected cycle
and spin speed.
DONE
Once the cycle is complete, this light will come on.
Remove the load promptly for best results.
LID LOCK
To allow for higher spin speeds, the lid will lock and
the Lid Locked light will turn on. When this light is lit,
the lid is locked and cannot be opened. When this
light is blinking, the washer is paused. When this light
is off, the lid can be opened.
If you need to open the lid, press
START/Pause. The lid will
unlock once the washer movement
has stopped. This may take several
minutes if the load was spinning at
high speed. Press START/Pause again to resume the cycle.
NOTE: If the START/Pause button is held for more than
3 seconds, the cycle will cancel and the washer will drain.
Not all features and options are available on all models.
Appearance may vary.
1
4