Filter
Top Products
34
ELECTRONIC CONTROL SETUP INSTRUCTIONS
WARM START (after power failure) – A few seconds after
power is restored, if a cycle was in progress at the time of the
power failure, “RESELECT CYCLE” will ash in the display,
indicating the need for a key press to restart washer or dryer.
WASHER DOOR LOCK – Prior to beginning a cycle, there is a
door lock routine of lock/unlock/relock, then cycle begins. The
door will remain locked until the end of a cycle or approximately
2 minutes after a power interruption.
PRICING – After the door is opened and then closed following
the completion of a cycle, the display indicates the cycle
price (unless set for free operation, where the display will ash
“SELECT CYCLE”). As coins are dropped or debit inputs arrive,
the display will change to lead the user through the initiation of
a cycle.
There are four (4) types of dryer pricing:
Fixed “Vend” Pricing
A dryer setup for “Fixed Cycle” operation can only accept
additional time accumulated by increments equal to the length
of a complete dry cycle. A maximum of 99 minutes may be
purchased; no additional credit is given for coins dropped
with 99 minutes in the display.
Accumulator Pricing
If the price is set to one coin 1, then accumulator pricing
is in effect. Cycle time can be purchased one coin at a time
(PD models) up to the maximum time of 99 minutes.
Fixed Cycle With Top Off Pricing
A dryer set to offer “Top Off” capability will allow time to be
added to an existing dry cycle in increments equal to the
number of minutes of dry time per quarter (coin 1), up to 99
minutes, regardless of the cost required to start the dryer. No
credit is given for coins or debit inputs entered when the control
is displaying 99 minutes.
PR Models: In Enhanced Debit Mode, the top off price can be
set independently (see VALUE OF COIN 2), and the top off time
is calculated according to the following equation:
top off time = x full cycle length
Penny increment offset is not applied to top off purchases.
FREE CYCLES – This is established by setting the cycle price
to zero. When this happens, “SELECT CYCLE” will appear
rather than a cycle price. Any cycle started as a free cycle
will automatically terminate when the door is opened.
DEBIT CARD READY – This washer/dryer is debit card
ready. It will accept a variety of debit card systems, but does
NOT come with a debit card reader. Refer to the debit card
reader manufacturer for proper washer/dryer setup. In models
converted to a Generation 1 debit card system, debit pulses
represent the equivalent of one coin (coin 1).
Control Set-up Procedures
IMPORTANT: Read all instructions before operating.
PD/PR Models: Insert service switch key and turn
counterclockwise.
PR Models: Once a Generation 2 debit card reader is installed
(according to the reader manufacturer’s instructions), the
set-up modes can only be changed by inserting a set-up
card (supplied by the reader manufacturer) into the card slot.
Inserting the service switch key and turning will only allow
access to the service mode.
The washer/dryer is now in the set-up mode. The lower fabric
setting buttons and the lower portion of the display are used
to set up the digital control for the washer. The upper three
fabric setting buttons and the upper portion of the display
are used to set up the controls for the dryer.
The display can contain 4 numbers and/or letters
and a decimal point on both the top and bottom display
portions. These are used to indicate the set-up codes and
related code values available for use in programming the
washer/dryer.
How to Use the Buttons to Program the Controls
1. The lower-left (PERM. PRESS) button is used to adjust the
values associated with washer set-up codes and the upper-
left (WHITES & COLORS) button is for the dryer. Pressing
the button will change the value by increments. Rapid
adjustment is possible by holding the button down.
2.
The lower-middle (DELICATES AND KNITS) button will
advance through the set-up codes. Pressing the button will
advance both the washer and dryer to the next available
set-up code. Some set-up codes are washer- or dryer-
specic and will not be displayed on both the washer and
dryer portions of the display. Holding down the lower-middle
(DELICATES AND KNITS) button will automatically advance
through the set-up codes at a rate faster than 1 per second.
3.
The lower-right (QUICK CYCLE) button is used to select or
deselect washer options; upper-right (DELICATES) is used for
dryer option selection or deselection.
top off price
full cycle price