Filter
Top Products
Troubleshooting Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless
testing requires power.
June 2006 9 16026882
©2006 Maytag Services RPL 16026127
IN
Board Input Test
While in Service Mode, pressing the
Spin Only key will begin the Board Input
Test. This test turns on a specified output
after a key press. Pressing the Spin Only key again
cancels the test. (Display shows “in”).
While in Service Mode follow chart to check respective
function.
• When the Rotary Cycle Selector knob is set to
“Super Wash
” and the Rotary Cycle Selector knob
is pressed, the door position will be displayed: “0P” if
open, “CL” if closed.
• When the Rotary Cycle Selector knob is set to
“Normal
” and the Rotary Cycle Selector knob is
pressed, the Lock position will be displayed: “UL” if
unlocked, “L0” if locked.
• When the Rotary Cycle Selector knob is set to
“Whites
” and the Rotary Cycle Selector knob is
pressed, the High water level will be displayed: “
–
0”
if below level, “
–
1” if above level. The High water
level is defined as the over flow water level.
• When the Rotary Cycle Selector knob is set to
“Wrinkle Control
” and the Rotary Cycle Selector
knob is pressed, the Medium water level will be
displayed: “—0” if below level, “—1” if above level.
The Medium water level is defined as the minimum
water level needed such that the heater can be
turned ‘ON’ (only MAH8700* and MAH9700* models
have heaters).
• When the Rotary Cycle Selector knob is set to
“Colors
” and the Rotary Cycle Selector knob is
pressed, the Low water level will be displayed: “_0” if
below level, “_1” if above level. The Low water level
is defined as the reset water level.
• When the Rotary Cycle Selector knob is set to
“Hand Wash
” and the Rotary Cycle Selector knob
is pressed, the level of Tub unbalance will be
displayed: “UC” if balanced, “U0” if unbalanced. “U0”
will be displayed during the time when the machine
is correcting for the unbalance; e.g. slowing down to
redistribute the load or to get to a lower spin speed.
Once the situation has been corrected (i.e. the load
has begun tumbling or the lower speed has resulted
in an acceptable amount of balance); “UC” will once
again be displayed.
• When the Delay key is pressed, the water
temperature will be displayed in Degrees F
(Fahrenheit).
• When the Rotary Cycle Selector knob is set to
“Delicates
” and the Rotary Cycle Selector knob is
pressed, the water temperature will be displayed in
degrees C (Celsius).
• When the Rotary Cycle Selector knob is set to
“Super Wash
”, the LED lights up. Revolve Rotary
Cycle Selector knob clockwise until all LED’s are
‘OFF’, then press Rotary Cycle Selector knob to
display frequency reading. “2560” means 25.60 Hz
(washer empty).Frequency value drops as water
rises.
While performing the Board Input Test in Service
Mode, follow this quick reference chart to check
respective functions.
Selection Function Display
Rotary Cycle
Selector set to
“Super Wash
”.
Press Rotary Cycle
Selector.
Door position
“0P” or “CL”
Rotary Cycle
Selector set to
“Normal
”. Press
Rotary Cycle
Selector.
Lock state
“UL” or “L0”
Rotary Cycle
Selector set to
“Whites
”. Press
Rotary Cycle
Selector.
High water
level
“
–
0” if below
level. “
–
1” if
above level.
Rotary Cycle
Selector set to
“Wrinkle Control
”.
Press Rotary Cycle
Selector.
Medium water
level
“—0” if below
level. “—1” if
above level.
Rotary Cycle
Selector set to
“Colors
”. Press
Rotary Cycle
Selector.
Low water level
“_0” if below
level. “_1” if
above level.
Rotary Cycle
Selector set to
“Hand Wash
”.
Press Rotary Cycle
Selector.
Tub balance
“UC” if
Balanced. “U0”
if Unbalanced
Press Delay key.
Water
temperature
Degrees F
Rotary Cycle
Selector set to
“Delicates
”. Press
Rotary Cycle
Selector.
Water
temperature
Degrees C
All cycle LEDs are
off, press Rotary
Cycle Selector
Water Level
Frequency(Hz)
“2560” (empty).
Frequency
drops as water
rises.