Filter
Top Products
The water level sensor is bad.
Please contact the after-sales
service department.
The digitron displays E6.
Phenomena The reason How to settle
Thetop lid is not closed
Is the drain hose put down?
Is the drain hose blockedby
foreignmaterial?
Arethe laundries put slantingly?
Arethe laundries slantingin
spinning?
Is the machine slanting?
Is the machine slanting?
Thewater tap is not open
Thewater inlet valve is blocked
The water pressure is too low
and the current is too small
Is there power failure?
Is the power plug loose?
Is the jointer screw of thewater
inlet hose is loose or twisted
awry?
Thewater faucet leaks
There's abnormal soundinside the
machine
Themachine does
not act
Close the top lid
Put down the drain hose. Open
andclose the top lid once.
Cleanthe foreign material.
Open and close the top lid once.
Re-orderthe laundries. Close the
top lid.Level the machine in right
position.
Open and close the top lid once.
Open the water tap. Push
the "Start/Pause" button.
Clean the water inlet valve.
Push the "Start/Pause" button.
Wait for the normal water pressure
Before use.
Useitwhen the power is on.
Insert the power plug tightly.
Level the machineproperly.
Re-order the laundries.
Fastenthe jointer screw
properly.
Does the water level arrive at the
set water level?
Affusion to theset water level.
Is the power plug loose?
Insert the power plug tightly.
Is the top lid closed?
Close the top lid
Arethe laundries put orderly?
Put the laundries orderly.
Not spin
Not wash
Buzzing upon reservation starts,
Nixie tube indicates"E0"
Safety switch actuates, not
spin,(after self-correction
twice), nixie tube displays
"E3",
buzzing
No or slow water filling (not
reaching the levelin 40 min),
nixie tube indicates
"E4",
buzzing
No or slow drain,nixie tube
indicates
"E1"
,buzzing.
If the nozzle is choked with
foreign bodies
Remove the foreign bodies
Poor or no waterfall flow
The top coverleaves open
Close the top lid
Running pauses during spin,
nixie tube indicates
"E2",
buzzing
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained performance inspection
by the factory.
Common phenomena
Phenomena
Explanation
The spinning is intermittent when it starts.
The wash procedure pauses.
Select spin program, but it does not work.
Balance the laundries to avoid slanting.
The cloth sensor is detecting , it will add water
after about 48 senconds.
The program is setting the drain time , certain
period is needed before it starts spinning.
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
16 1
(One piece)
Bottom plate
Water inlet hose
Tapping screw
Water inlet valve
Water absorption cushion
Power cord
Top lid components
Detergent box
Control panel
Outer tub cover
Balance ring
Inner tub
Lint filter(2pieces)
Pulsator
Control panel coating
Cabinet
Liquid wahitener inlet
Adjustable leg
Rear faceplate
Honourable users:
Thank you for choosing our products.
Our products integrate high-tech, precision, frontier science .To facilitate using it,
please read this manual carefully and operate this machine according to it.
Back cover
Drain hose
Contents marked with that symbol
are related to the safety of the
product and the personal safety
of the users. Please operate in strict
conformity to the contents, otherwise
it may result in damage of the
machine or influence the personal
safety of the users.
Contents marked with that symbol
are actions forbidden to perform.
Performing of those actions may
result in damage of the machine
or influence the personal safety
of the users.
the end connecting to
the washing machine
jointer connecting the water
inlet hose and the water faucet
the end connecting to the
water inlethose jointer
Water inlet hose jointer
Accessories
Meaning and description of the symbols
(One piece)
(One piece)
The figure in this manual being sketch map and with the improvement of our products, the machine you buy
is like to be different from the figure indicated in the manual .Please understand.
Before Using
Before Using
Handle
Draining hose
hanging hole
Names of the parts
(Eight pieces)