Filter
Top Products
>10mm
7
About less than 2mm after twisting
Figure 3
Connection between the water inlet hose jointer and the water faucet
Bushing
About 4mm before twisting
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
Water faucet,not suitable
Install the water inlet hose
Screw
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Remark: Before installation, the threading is 4mm above the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
Figure 6
Signplate
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Figure 2
Screwnut
Screw knife
3.Fasten the four screws evenly. See to Figure 4.
water inlet hose jointer
Figure 5
Outlet end surface
Slider
Figure 1
Water faucet,suitable
water inlet hose
Figure 4
Lock level
Confirm the water faucet
10
The capacity of washing of themachine refer to the largest weight of the
standard laundries under dry condition that can be washed inone
time. Laundries quantity in one washing cycle shall be lower than
the standard capacity.
The thickness ,size , type of the cloth will influence the actual washing capacity.
It is suitable to put in reasonable amount of laundries and the laundries can be turned
round in washing for one time washing.
Do not select " 4" water level forlaundries lessthan 1.0kg ,so as to avoid
splashing of water.
Put in the laundries
How to use the whitener
How to use the washing powder
Washing powder with poor quality or long-time storage may
get caked. Please clean the detergent box duly in usage.
Dissolve directly inside the washing machine: (not
applicable for fuzzy and reserve program)
1.Add some water(select"1"water level).
2.Add washing powder. Run for about 30s to fully dissolve
the power.
Then push the"START/PAUSE" button.
3.Put in laundries. Select suitable water level. Push the
"START/PAUSE"button again.
Quick dissolving of washing powder:
1.Prepare warm water of 30 C and container.
2.Add washing powder while stirring to dissolve it completely.
It is not recommended to use rich-foam washing powder.
Usage of detergent
If you select program, it is suggested to use
liquid detergent instead of washing powder to guarantee
the washing effect.
"Speedy"
Please add suitable washing powder as per the laundries
quantity, the set water level and water quantity.
It is suggested to add washing powder into the box
directly under fuzzy program and reserve program.
The whitener shall not touch laundries directly.
Add water to decided level. Dilute the whitener with container,
and then pour it into the liquid whitener inlet slowly.
Laundries with color or pattern is not colorfast, thus not applicable.
For whitener in powder, dissolve it before use.
See to the manual of whitener for the usage and dosage.
The usage and dose of the softener as per the specifications of softener.
Before washing put the softener into the hole directly as indicated in the
left figure The softener will put into the washer when the last rinsing.
Refer to the following list for the usage of the detergent:selection of the
water level,water quantity and dosage of detergent
After the softener is put in, please don't place for a long time otherwise
softener may solidify and cause flowing not smooth.
Remark: Do not use softener if rinse times is not two.
How to use the softner
Control panel seat
Liquid detergent inlet
Access for detergent and washing powder
Detergent box
Access for softener