Filter
Top Products
After you open the package, please lean
the washing machine gently down on soft
items ( like the towel cloth, blanket, etc. ).
Install the bottom plate to the bottom of
the machine, then lift the machine up
gently. See to the figure:
Back
Front
Soft items
Bottom plate
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
Install the bottom plate
Installation and adjustment
I
Section I enlarging
Two claws at the bottom cover shall
be inserted in two bar-shaped holes
in the stand. Make sure the claws
are firmly in place.
Fasten the bottom plate to
base frame with one screw
Install the inner cover component
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aiming the inner cover
shaft to the installation hole of the corresponding outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of one side into the corresponding outer tub
cover shaft groove, then push the another inner cover shaft into the corresponding outer
tub cover shaft groove. Please install to designated position to guarantee there are no
dropping or abnormal sound in opening and closing of the inner cover, and the operation
shall be smooth. Do not dismount the inner cover component after washing.
Outer tub cover
Outer tub cover shaft groove
Inner cover shaft
Inner cover component
Figure 1
Right hand
Left hand
Figure 2
1.Push "POWER" button to switch on the power
2.Push "PROGRAM" button to select suitable full-auto program
Steps of using the operation buttons and description of each step
After the power is switched on, "STANDARD" is automatically set. To select other full-auto programs, please push
the "PROGRAM" button till the corresponding indicator is on. Refer to the "PROGRAM" button on Page 11.
E.g. Set to "SPEEDY"program for small quantity of laundries with light soil.
When a standard cycle is selected, the fuzzy program is run. The water level and the washing time can be
selected according to be texture and volume of the laundry. The washing cycle is automatically controlled.
I DELAY button
"+ - "
Push down the to select the reserve time(2h-24h)."+ - "
Push the buttoncan display the reserve state."+ - "
SOAK
ForGENTLEprogram, press SET buttoncanchangetheprocess,
cannotchangetime.
"SOAK"button,thenpress "+ -"
J "SOAK " button
K Reserve, remain time digitron
It displays "--" during detecting.
It displays remained reserve time (hour).
It displays abnormal symbol in abnormal situation.(See to Page16)
You can choose"RESERVE WATER" functionto keepthe afterrinsing water.
Washingmachine will keep theafter rinsing wateronce finish rinsingin tub about4 hours, andbuzzer every 15
minutes.( Forexample, ifyou choose"SECOND RINSE",the machineonly keepthe aftersecond rinsing water,
If youchoose "FIRSTRINSE" and "SECONDRINSE" together,the machinewill keepthe afterfirst andsecond
rinsing water)
Press"START/PAUSE" buttonor openand closethe toplid onetime to collectthe after rinsingwater,then the
machine willgo onfor nextprogram.
If youdon't collectthe afterrinsing waterwithin 4hours, themachine will drainautomaticly,then goon for
next program.
L RESERVE WATER" " button
M SET "+ - " button
Refer to the description of operation button
13
RESERVE
WATER
Thebuttonisunavailablefrom theSPEEDY,WOOLandTUBDRYprograms.
Ithasthespecialpowerresumefunction.Inthecaseofpowerfailureorthepowerplugisloose
duringrunning,themachinecansavetherunningprogram,andresumetheprogramafterthe
powersupplyisrecovered.Youdonotneedtosettheprogramagain.
Pressthe button,thelight flashesthenpress SET toselectthedesiredsoaktime
fromtheSTANDARD,HEAVY,CHILD,MEMORYprograms(0,10,20,30,40minutes).
"SOAK""+-"
Pressthe buttontoselectsoak ."SOAK" procedure