Blomberg WNF 7361 SCE20 Washer User Manual


  Open as PDF
of 68
 
12
EN
active, previously selected programme will continue
running.
ToactivatetheChildLock:
Pressandhold1
st
and 2
nd
Auxiliary Function buttons for
3seconds.Thelightsonthe1
st
and 2
nd
Auxiliary Function
buttonswillflash,and"C03","C02","C01"willappearonthe
display respectively while you keep the buttons pressed for
3 seconds. Then, "Con" will appear on the display indicating
thattheChildLockisactivated.Ifyoupressanybuttonorturn
theProgrammeSelectionknobwhentheChildLockisactive,
samephrasewillappearonthedisplay.Thelightsonthe1st
and 2nd auxiliary function buttons that are used to deactivate
theChildLockwillblink3times.
TodeactivatetheChildLock:
Pressandhold1
st
and 2
nd
auxiliary function buttons for 3
seconds while any programme is running. The lights on the
1
st
and 2
nd
AuxiliaryFunctionbuttonswillflash,and"C03",
"C02","C01"willappearonthedisplayrespectivelywhile
you keep the buttons pressed for 3 seconds. Then, "COFF"
willappearonthedisplayindicatingthattheChildLockis
deactivated.
C
Inadditiontothemethodabove,todeactivatetheChild
Lock,switchtheProgrammeSelectionknobtoOn/
Off position when no programme is running, and select
another programme.
C
ChildLockisnotdeactivatedafterpowerfailuresor
when the machine is unplugged.
C
IfyouswitchoffthemachinebypressingtheOn/Off
buttonwhentheChildLockisactiveandthemachineis
running, then the child lock will be deactivated.
Progress of programme
Progress of a running programme can be followed from the
ProgrammeFollow-upindicator.Atthebeginningofevery
programme step, the relevant indicator light will turn on and
light of the completed step will turn off.
You can change the auxiliary functions, speed and
temperature settings without stopping the programme flow
while the programme is running. To do this, the change
you are going to make must be in a step after the running
programmestep.Ifthechangeisnotcompatible,relevant
lights will flash for 3 times.
C
Ifthemachinedoesnotpasstothespinningstep,
RinseHoldfunctionmightbeactiveortheautomatic
unbalanced load detection system might be activated
due to the unbalanced distribution of the laundry in the
machine.
Loading door lock
There is a locking system on the loading door of the machine
that prevents opening of the door in cases when the water
level is unsuitable.
Loadingdoorlightwillstartflashingwhenthemachine
is switched to Pause mode. Machine checks the level of
thewaterinside.Ifthelevelissuitable,LoadingDoorlight
illuminatessteadilywithin1-2minutesandtheloadingdoor
can be opened.
Ifthelevelisunsuitable,LoadingDoorlightturnsoffandthe
loadingdoorcannotbeopened.Ifyouareobligedtoopen
theLoadingDoorwhiletheLoadingDoorlightisoff,you
havetocancelthecurrentprogramme;see"Cancelingthe
programme".
Changing the selections after
programme has started
Switching the machine to pause mode
PresstheStart/Pausebuttontoswitchthemachinetopause
mode while a programme is running. The light of the step
which the machine is in starts flashing in the Programme
Follow-upindicatortoshowthatthemachinehasbeen
switched to the pause mode.
Also,whentheloadingdoorisreadytobeopened,Loading
Doorlightwillalsoilluminatecontinuouslyinadditiontothe
programme step light.
Changing the speed and temperature settings for
auxiliary functions
Dependingonthesteptheprogrammehasreached,you
maycanceloractivatetheauxiliaryfunctions;see,"Auxiliary
function selection".
Youmayalsochangethespeedandtemperaturesettings;
see, "Spin speed selection" and "Temperature selection".
C
Ifnochangeisallowed,therelevantlightwillflashfor3
times.
Adding or taking out laundry
PresstheStart/Pausebuttontoswitchthemachineto
pausemode.Theprogrammefollow-uplightoftherelevant
step during which the machine was switched into the pause
modewillflash.WaituntiltheLoadingDoorcanbeopened.
OpentheLoadingDoorandaddortakeoutthelaundry.
ClosetheLoadingDoor.Makechangesinauxiliaryfunctions,
temperatureandspeedsettingsifnecessary.PressStart/
Pause button to start the machine.
C
The loading door will not open if the water temperature
in the machine is high or the water level is above the
door opening.
Canceling the programme
To cancel the programme, turn the Programme Selection
knob to select another programme. Previous programme will
becanceled.End/Cancellightwillflashcontinuouslytonotify
that the programme has been canceled.
Pumpfunctionisactivatedfor1-2minutesregardlessofthe
programme step, and whether there is water in the machine
or not. After this period, your machine will be ready to start
with the first step of the new programme.
C
Dependingonthestepwheretheprogrammewas
canceled in, you may have to put detergent and softener
again for the programme you have selected anew.
C
Ifyouwanttoopentheloadingdoorafteryouhave
cancelled the programme but it is not possible to open
the loading door since the water level in the machine
is above the loading door opening, then turn the
Programme Selection knob to Pump+Spin programme
and discharge the water in the machine.
End of programme
“End” appears on the display at the end of the programme.
Wait until the loading door light illuminates steadily. Press On
/Offbuttontoswitchoffthemachine.Takeoutyourlaundry
and close the loading door. Your machine is ready for the next
washing cycle.
 previous next