Blomberg WNF 5100 WE Washer User Manual


  Open as PDF
of 62
 
11
EN
Auxiliary function selection
Selectthedesiredauxiliaryfunctionsbeforestarting
the programme. Furthermore, you can also select
orcancelauxiliaryfunctionsthataresuitableto
the running programme without pressing the Start
/Pause/Cancelbuttonwhenthemachineis
operating.Forthis,themachinemustbeinastep
beforetheauxiliaryfunctionyouaregoingtoselect
or cancel.
Iftheauxiliaryfunctioncannotbeselectedor
canceled, light of the relevant auxiliary function will
blink3timestowarntheuser.
C
Somefunctionscannotbeselectedtogether.Ifa
second auxiliary function conflicting with the first
oneisselectedbeforestartingthemachine,the
functionselectedfirstwillbecanceledandthe
second auxiliary function selection will remain
active.
C
Anauxiliaryfunctionthatisnotcompatible
withtheprogrammecannotbeselected.(See
"Programmeandconsumptiontable")
C
AuxiliaryFunctionbuttonsmayvaryaccordingto
the model of the machine.
• Prewash
A Prewash is only worthwhile for heavily soiled
laundry. Not using the Prewash will save energy,
water, detergent and time.
C
As their meshed texture causes excessive
foaming,washtheveils/tullebyputtinglittle
amount of detergent into the main wash
compartment.Donotputdetergentinthe
prewash compartment.
• Rinse Plus
Thisfunctionenablesthemachinetomakeanother
rinsing in addition to the one already made after the
mainwash.Thus,theriskforsensitiveskins(babies,
allergicskins,etc.)tobeeffectedbytheminimal
detergentremnantsonthelaundrycanbereduced.
• Rinse Hold
Ifyouarenotgoingtounloadyourclothes
immediately after the programme completes, you
can use rinse hold function to keep your laundry
in the final rinsing water in order to prevent them
from getting wrinkled when there is no water in the
machine.
InmodelsequippedwithSpinSpeedAdjustment
button,selecttheSpinSpeedandpressStart/
Pause/Cancelbuttonifyouwanttospinthelaundry
held in water.
InmodelsnotequippedwithSpinSpeedAdjustment
button,selectSpin+Pumpprogrammeifyouwantto
spin your laundry held in water.
C
Inthesemodels,youneedtostopthemachine
bypressingStart/Pause/Cancelbutton
beforeswitchingtospinstepandafterpump
step is completed and the water in the machine
is drained. Thus, water inside the machine is
drained and your laundry is not spun.
• No Heat
Usethisfunctionifyouwanttowashyourlaundryin
cold water.
• No Spin
Usethisfunctionifyoudonotwantyourclothesbe
spun at the end of the programme.
• Spin speed reduction
This function allows spinning of laundry at a speed
lower than the maximum spin speed of the machine.
WhenSpinReductionbuttonispressed,spinspeed
willbelimitedtotheminimumspeedspecifiedonthe
control panel.
Starting the programme
PressStart/Pause/Cancelbuttontostartthe
programme.Start/Pause/Cancelbuttonlightsup
to indicate that the programme has started. Loading
doorislockedandLoadingDoorlightturnsoff.
Child Lock
UseChildLockfunctiontopreventchildrenfrom
tampering with the machine. Thus you can avoid any
changes in a running programme.
C
YoucanswitchonandoffthemachinewithOn
/OffbuttonwhentheChildLockisactive.When
you switch on the machine again, programme
will resume from where it has stopped with the
childlockenabled.
To activate the Child Lock:
Press and hold 1
st
and 2
nd
Auxiliary Function
buttonsfor3secondssimultaneouslyafterwashing
programme has started. The 1
st
Auxiliary Function
light flashes continuously.
To deactivate the Child Lock:
Childlockmustbedeactivatedtostartanew
programme after the programme has finished or to
interrupt a running program.
Press and hold 1
st
and 2
nd
AuxiliaryFunctionbuttons
for3secondssimultaneouslytodisablechildlock.
Progress of programme
Progressofarunningprogrammecanbefollowed
fromtheProgrammeFollow-upindicator.Atthe
beginningofeveryprogrammestep,therelevant
indicator light will turn on and light of the completed
step will turn off.
To change the auxiliary function, speed and
temperature settings while a program is running, you
need to switch the machine to Pause mode. Press
Start/Pause/Cancelbuttontoswitchthemachine
intoPausemode.Inthiscase,Start/Pause/Cancel
light flashes.
C
Ifthemachinedoesnotpasstothespinning
step,RinseHoldfunctionmightbeactiveorthe
automaticunbalancedloaddetectionsystem
mightbeactivatedduetotheunbalanced
distributionofthelaundryinthemachine.
Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases
whenthewaterlevelisunsuitable.
When machine is switched to Pause mode, it checks
thelevelofthewaterinside.Ifthelevelissuitable,
LoadingDoorlightilluminatessteadilywithin1-2
minutesandtheloadingdoorcanbeopened.
IftheLoadingDoorlightisnoton,LoadingDoor
cannotbeopened.Ifyouareobligedtoopenthe
LoadingDoorwhiletheLoadingDoorlightisoff,you
must cancel the current programme; see "Canceling
the programme".
 previous next