9-22 Process ECP-2E Specifications
Accelerator
To process VISION Premier Color Print Film, the accelerator replenisher flow rate may need to be increased. If only a
small amount of footage is processed no change in the flow rate should be required in the replenisher. For larger quantities of
VISION Premier Color Print Film (more than one tank turnover), it is recommended to increase the flow rate by approximately
20% and closely monitor the PBA-1 level and retained silver in the D-max area of the film.
Bleach
Persulfate Bleach
Only to be used in combination with accelerator solution.
Constituent Fresh Tank
Fresh and Seasoned Tank
Analytical Specifications
Fresh
Replenisher
Replenisher Analytical
Specifications
Accelerator
*
* Mixing the accelerator with high agitation for extended periods of time results in loss of some PBA-1 due to aerial oxidation. Mix the accelerator only
until all chemicals are dissolved.
(AB-1b) (AB-1bR)
Water 24- 38°C (75-100°F) 900 mL 900 mL
Sodium Metabisulfite (Anhydrous) 3.3 g 2.0 ± 0.5 g/L
†
† The analytical method measures the total sulfite content of the solution and reports it as sodium metabisulfite (Na
2
S
2
O
5
). If a solution addition to the
sodium metabisulfite level must be made but sodium bisulfite is to be used, multiply the sodium metabisulfite addition weight by the factor 1.09 to
obtain the equivalent amount of sodium bisulfite.
The difference between mix level and the analytical specification occurs because some sulfite is consumed in a reaction with KODAK Persulfate
Bleach Accelerator PBA-1 to form the active accelerator species “in situ.”
5.6 g 3.3 ± 0.5 g/L
†
Acetic Acid (Glacial) 5.0 mL 5.0 ± 0.5 mL/L
‡
‡ The analytical method measures buffer capacity and results are reported in terms of glacial acetic acid. Adjustment in pH should be made with
glacial acetic acid or 50% sodium hydroxide.
7.0 mL/L 7.0 ± 0.5 m/L
‡
Persulfate Bleach Accelerator PBA-1
or
KODAK liquid PBA-1
§
§ For convenience, add PBA-1 from a 250 g/L stock solution. Prepare by dissolving 5 kg PBA-1 in water and diluting to 20 L. Each 4 mL of stock
solution contains 1 g PBA-1. For a 100 L replenisher of AB-1bR, add 1.96 L of stock solution.
3.3 g
or
4.0 mL
3.3 ± 0.3 g/L
or
4.0 ± 0.4 mL/L
4.9 g
or
5.9 mL
4.9 ± 0.3 g/L
or
5.9 ± 0.4 mL/L
(Ethylenedinitrilo)
Tetraacetic Acid Tetrasodium Salt
0.5 g 0.7 g
Water to make 1 L 1 L
pH at 25.0°C (77.0°F) 4.0 ± 0.2 3. ± 0.2
Specific Gravity at 25.0°C (77.0°F) 1.007 ± 0.003
1.031 ± 0.003
(seasoned)
1.012 ± 0.003
Constituent Fresh Tank
Fresh and Seasoned Tank
Analytical Specifications
Fresh
Replenisher
Replenisher Analytical
Specifications
Persulfate Bleach (SR-30) (SR-30R)
Water 24-38°C (75-100°F) 850 mL 800 mL
Chlorine Scavenger
*
* Since there are many acceptable chlorine scavengers, convenience of use and cost may be factors in making a choice. Hydrolysate, a soluble version
of gelatin, is available from U.S. Gelatin Corporation. Both food and photographic-grade gelatin have been used successfully. The gelatin must first
be dissolved in 40°C (104°F) water and stirred for 20 minutes. Up to 50 g/L can be added in this way in order to make a stock solution for subsequent
use. Beta-aminopropionic acid is higher cost alternative offering easy solubility.
0.35 g 0.50 g
Sodium Persulfate 33 g 30 ± 2 g/L 52 g 48 ± 3 g/L
Sodium Chloride 15 g 15 ± 3 g/L 20 g 20 ± 2 g/L
Sodium Dihydrogen Phosphate
(Anhydrous)
7.0 g 10.0 g
Phosphoric Acid (85%) 2.5 mL 7.0 ± 1.0 mL/L
†
† The analytical method measures the buffer capacity of the bleach and reports the result as mL/L of phosphoric acid (85%). The analytical
specification (7.0 mL) is larger than the amount of phosphoric acid added (2.5 mL) because dihydrogen phosphate (and sulfate in seasoned
solutions) also contributes to the measurement. If a correction must be made, phosphoric acid (85%) can be added on a mL-for-mL basis. For
example, if the tank analysis reports 5.0 mL/L, then the correction would be to add 2.0 mL/L of phosphoric acid (85%).
2.5 mL 8.8 ± 1.0 mL/L
†
Water to make 1 L 1 L
pH at 25.0°C (77.0°F) 2.3 ± 0.2 2.4 ± 0.2
Specific Gravity at 25.0°C (77.0°F) 1.037 ± 0.003 (fresh)
1.085 (seasoned)
‡
‡ If the bleach tank overflow is being reused, the specific gravity (a measure of sulfate ion buildup) should not exceed this value as incomplete
bleaching could occur.
1.059 ± 0.003
