ENGLISH
Remote
Control
Playback
(Advanced)
Connections
Simple
Version
Playback
(Basic)
Multi-
zone
GUISettings
Getting
Started
Troubleshooting
Other
Information
Spec. Index
Part
Names
Manual Setup
Audio Setup
Default settings are underlined.
Set the audio input and output.
Setting items Setting details
COAX Input Assign
Assign coaxial digital
connector.
OFF : Do not assign coaxial digital connector.
AUX1 : Sets to the digital audio input connector for AUX1.
AUX2 : Sets to the digital audio input connector for AUX2.
NOTE
When set to “AUX1” or “AUX2”, priority is given to output of COAXIAL
input signals over analog or OPTICAL input signals.
Dynamic Play Mode
When playing back on a
2.0/2.1-channel setup, the
unused surround channels
(amps) are used together
with the front channels
(amps) to give improved
sound quality.
AUTO : Automatically ON when parallel drive possible.
OFF : Parallel drive is not performed.
Option Setup
Default settings are underlined.
Make various other settings.
Setting items Setting details
Volume Control
Set the MAIN ZONE (room
where the unit is located)
volume setting.
Volume Limit : Make a setting for maximum volume.
OFF : Do not set a maximum volume.
60 / 70 / 80
•
•
Power On Level : Define the volume setting that is active when the
power is turned on.
Last : Use the memorized setting from the last session.
0 – 99 : The volume is adjusted to the set level.
•
•
GUI
Make GUI related settings.
Screensaver : Make screensaver settings.
ON : If is no operation is performed for approximately three minutes
while the GUI menu or iPod playback screen is displayed, a screen saver
is activated. When you press uio p, the screen saver is cancelled
and the screen before that screen saver started is displayed.
OFF : Screen saver is not activated.
•
•
Setting items Setting details
GUI
(Continued)
Text : Display the details of operation when switching surround mode,
input mode, etc.
ON
OFF
•
•
Master Volume : Display the master volume during adjustment.
Bottom : Display at the bottom.
Top : Display at the top.
OFF : Turn display off.
When the master volume display is hard to see when superimposed
on movie subtitles, set to “Top”.
•
•
•
Quick Start Mode
Make Quick Mode settings.
ON : Start up time is faster but power consumption during standby is
higher.
OFF : Turn off Quick Mode.
Remote Preset Codes
By registering the preset
codes in the supplied
remote control unit, you can
operate a TV, satellite tuner
or cable TV made by other
manufacturers.
1. Select the device you want to register using ui and press ENTER to
confirm.
2. Select the first letter of the manufacturer’s name using ui and press
ENTER to confirm.
3. Select the manufacturer’s name using ui and press ENTER to
confirm.
4. The procedures for registering remote control codes and remote
control preset registration are displayed.
Some devices you want to register may have more than one preset code.
In this case, after registering the preset code, try operating the device
with the remote control unit to check that it is working properly.
For details on operating devices with the remote control unit after
registering the preset code, see “Operating Components” (vpage
59).
•
•
Trigger Out
Select the condition for
activating Trigger Out for
the input source, surround
mode, etc.
See “TRIGGER OUT Jacks”
(vpage 17) for more
information on trigger out.
When Setting for Zone (MAIN ZONE/ZONE2):
Trigger out is activated through linkage to the power of the zone set to
“ON”.
When Setting for Input Source:
Activate trigger out when the input source set to “ON” is selected.
Active for the zone set to “ON” with “When Setting for Zone”.
When Setting for Surround Mode:
Activate trigger out when the surround mode set to “ON” is selected.
Active when the “MAIN ZONE” set to “ON” with “When Setting
for Zone” is selected, and when the input source set to “ON” with
“When Setting for Input Source” is selected.
ON : Activate trigger on this mode.
– – – : Do not activate trigger on this mode.
•
•
Remote control operation
buttons
Display the menu
Cancel the menu
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
