0
Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifications
Make the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey™ Auto Setup)
s Audyssey Auto Setup Preparations
around items indicate the settings.
Perform the following settings if adjustments, etc., are required for the speaker environment you’re using.
If you do not need to perform the following settings, or have already completed them, select “Auto Setup Start” and then press ENTER.
Proceed to “
STEP2
”.
When you are using surround back speakers with ZONE2/ZONE3,
set to “ZONE2” or “ZONE3”.
You can set in the same way as described in “Amp Assign” on page
34.
•
•
When “Amp Assign” is set to “Normal”, only then is “Surround Back”
displayed.
Change the Amplifier Assignment (Amp Assign)
The signal output from the SURR.BACK/AMP ASSIGN speaker
terminal of the AVR-4310CI can be switched to match your speaker
environment (vpage 34 “Amp Assign”).
Set the Channels You will not Use (Channel Skip)
If you set the channels you will not use beforehand, those channels
will not be measured. Therefore, you can save an amount of time
commensurate with that which would have been taken to measure
those channels.
1
Select “Amp Assign”
and then press
ENTER.
2
Press ui to select an item, and then press ENTER.
Normal
ZONE2
ZONE3
ZONE (MONO)
Bi-Amp
2CH
Front Height
Front Wide
: Outputs surround back channel audio.
: Outputs ZONE2 audio.
: Outputs ZONE3 audio.
: Outputs ZONE2 / ZONE3 monaural audio.
: Outputs front channel audio for bi-amp use.
: Outputs front channel audio during 2-channel
DIRECT and STEREO mode.
: Outputs front height channel audio.
: Outputs front wide channel audio.
To cancel, press
RETURN.b
1
Select “Channel
Skip” and then press
ENTER.
2
Press ui to select a channel, press o p to select
the item, and then press ENTER.
Configurable channelsn
Subwoofer
Surround B
Surround Back
: Set the subwoofer channel.
: Set the surround B channel.
: Set the surround back channel.
Settingsn
Measure
Skip
: Default setting. Measure the selected channel.
: Skip the selected channel and do not measure.
To cancel, press
RETURN.b
NOTE
Since “Amp Assign” of AVR-4310CI is set to “ZONE2” by default,
audio is not output from the surround back speakers. When using the
surround back speakers with MAIN ZONE, change the “Amp Assign”
setting to “Normal”.
Audyssey Auto Setup detects the presence of each speaker and
automatically calculates the speaker size, channel level, distance and
crossover frequency settings. In addition, acoustical distortions are
corrected within the listening area.
When measuring begins, a test tone is output from each speaker.
Position and connect all speakers before commencing Audyssey
Auto Setup.
•
•
•
STEP2 Speaker Detection
1
Select “Measure” and
then press ENTER.
q Measure the subwoofer
level
To stop measuring, select
“Cancel” and then press
ENTER.
b
When “Subwoofer” is set to “Skip” with “Channel Skip”, this
measurement is not taken, and the process proceeds to “w
Measure each speaker”.
w
Measure each speaker
Once the measurements in step q are complete, the
measurements in step w start automatically.
The measuring channel changes depending on the setting of
“Amp Assign” (vpage 30) and “Channel Skip” (vpage 30).
When an error message is displayed, check “Error Messages” for
details (vpage 32).
e Check the speaker detection results
When measuring ends, the speaker detection results are
displayed.
Select “Next → Measurement” and press ENTER to proceed to
“
STEP3
”.
Press u to select “Retry”, and when you press ENTER, measuring
at the main listening position starts again.
b
b
b
b
b
d Perform Audyssey Auto Setup
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting :Return to previous menu
Setting
STEP1 Preparation
See overleaf