Filter
Top Products
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent required, pour it into the
main wash compartment
or in the appropriate com-
partment if the selected programme/option it requires
(see more details in "Detergent dispenser drawer").
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
«MAX» mark in the drawer). Close the drawer gently.
Select the required programme by turning the
programme selector dial (1)
Turn the programme selector dial to the required pro-
gramme. The washing machine will automatically select
the maximum spin value provided for the programme you
have chosen. You can change this value by pressing the
corresponding button. The green pilot light of the button
5 starts to flash.
The selector dial can be turned either clockwise or coun-
terclockwise. Turn to position
to reset programme/
Switching the machine off.
At the end of the programme the selector dial must be
turned to position
, to switch the machine off.
Caution! If you turn the programme selector dial to
another programme when the machine is working,
the red pilot light of button 5 will blink 3 times to indicate
a wrong selection. The machine will not perform the new
selected programme.
Select the spin speed or Rinse Hold option by
pressing button 2
The relevant light will light up.
When selecting a programme, the light corresponding to
the maximum speed allowed for that programme will il-
luminate.
Select the available options by pressing buttons 3
and 4
Depending on the programme, different functions can be
combined. These must be selected after choosing the de-
sired programme and before starting the programme.
When these buttons are pressed, the corresponding pilot
lights illuminate. When they are pressed again, the pilot
lights go out. If an incorrect option is selected, the inte-
grated red pilot light of the button 5 flashes for 3 times.
For the compatibility among the washing pro-
grammes and the options see chapter «Washing
Programmes».
Start the programme by pressing button 5
To start the selected programme, press the button 5 , the
corresponding green pilot light stops blinking. The pilot
light corresponding to the running phase illuminates. The
appliance starts operating and the door is locked.
To interrupt a programme which is running, press the
button 5 : the corresponding green pilot light starts blink-
ing.
To restart the programme from the point at which it was
interrupted, press the button 5 again . If you have chosen
a delayed start, the machine will begin the countdown.
If an incorrect option is selected, the red pilot light of the
button 5 blinks 3 times.
Interrupting a programme
Press the button 5 to interrupt a programme which is
running, the corresponding green pilot light starts blink-
ing.
Press the button again to restart the programme.
Cancelling a programme
Turn the selector dial to to cancel a programme which
is running. Now you can select a new programme.
Opening the door
After the programme has started the door is locked. If, for
any reason, you need to open it, set firstly the machine to
PAUSE by pressing the button 5 . After a few minutes it
will be possible to open the door.
If the door remains locked, this means that the machine
is already heating or that the water level is too high. In
any case, do not try to force the door!
If you cannot open the door but you need to open it you
have to switch the machine off by turning the selector dial
to
. After a few minutes the door can be opened (pay
attention to the water level and temperature!) .
After closing the door, it is necessary to select the pro-
gramme and options again and to press button 5 .
At the end of the programme
The machine stops automatically. The pilot light of button
5 and the pilot light corresponding to the just finished
washing phase go off. The light 7.3 illuminates. After a
few minutes the door can be opened.
If a programme or an option that ends with water left in
the tub has been selected, the light 7.3 illuminates but the
door remains locked to indicate that the water must be
emptied out before opening the door.
Follow the below instructions to empty out the water:
1.
Turn the programme selector dial to
.
7