Filter
Top Products
13
TROUBLESHOOTING
If you experience Possible Causes Solution
Vibration or Off-Balance
Vibration, rocking, or
“walking”
Feet may not be in contact with the
oor and locked.
Front and rear feet must be in rm contact with oor, and washer
must be level to operate properly. Jam nuts must be tight against
the bottom of the cabinet.
Washer may not be level. Check oor for exing or sagging. If ooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer will reduce sound.
See “Level the Washer” in the Installation Instructions.
Vibration during spinning
or washer stopped with
all dial lights ashing
Load could be unbalanced. Load garments in loose heaps evenly around the washplate.
Do not load garments directly over the center of the washplate.
Adding wet items to washer or adding more water to basket
could unbalance washer.
Avoid washing single items. Balance a single item such as a rug
or jeans jacket with a few extra items. If the dial is ashing, redis-
tribute the load, close the lid, and press START/PAUSE.
Use Bulky Items cycle for oversized, non-absorbent items
such as comforters or poly-lled jackets. Other items are
not appropriate for Bulky Items cycle. See “Cycle Guide.”
Item or load not suitable for selected cycle. See “Cycle Guide”
and “Using Your Washer.”
Noises – For normal operating sounds, go to www.whirlpool.com/product_help.
Clicking or metallic
noises
Objects caught in washer drain
system.
Empty pockets before washing. Loose items such as coins
could fall between basket and tub or may block pump. It may be
necessary to call for service to remove items.
It is normal to hear metal items on clothing such as metal snaps,
buckles, or zippers touch against the stainless steel basket.
Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming
sound with periodic gurgling or surging as nal amounts of water
are removed during the spin/drain cycles.
Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have
started the washer. This is normal.
Water Leaks
Check the following for
proper installation:
Washer not level. Water may splash off basket if washer is not level.
Fill hoses not attached tightly. Tighten ll-hose connection.
Fill hose washers Make sure all four ll hose at washers are properly seated.
Drain hose connection Pull drain hose from washer cabinet and properly secure it to
drainpipe or laundry tub.
Do not place tape over drain opening.
Check household plumbing for leaks
or clogged sink or drain.
Water can back up out of a clogged sink or drainpipe. Check all
household plumbing for leaks (laundry tubs, drain pipe, water
pipes, and faucets.)
Washer not loaded as
recommended.
An unbalanced load can cause basket to be out of alignment
and cause water to splash off tub. See “Using Your Washer”
for loading instructions.
Washer not performing as expected
Not enough water
in washer
Load not completely covered
in water.
This is normal operation for an HE low-water washer. The load
will not be completely underwater. The washer senses load
sizes and adds correct amount of water for optimal cleaning.
See “What’s New under the Lid.”
IMPORTANT: Do not add more water to washer. Adding water lifts
the garments off the washplate, resulting in less effective cleaning.
Washer won’t run or ll,
washer stops working
Check for proper water supply. Both hoses must be attached and have water owing to inlet
valve.
Both hot and cold water faucets must be turned on.
Check that inlet valve screens have not become clogged.
Check for any kinks in inlet hoses, which can restrict water ow.
First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -
In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.