Filter
Top Products
12
Main Wash detergent compartment
(Number 3 in Dispenser Illustration)
Add liquid or powdered detergent to this compartment for your
main wash cycle. The detergent separator must always be in
place, either in the front or back position.
IMPORTANT:
If you are using the Prewash option or the Auto
Soak with a wash cycle, powdered detergent must be used in the
Main Wash compartment since liquid detergents may seep out of
the Main Wash compartment during the prewash, soak time, or
delay before the main wash begins.
■
Do not fill beyond the “MAX” level.
■
Liquid or powdered color-safe bleach may be added to the
Main Wash compartment along with the same type of
detergent, liquid or powdered.
■
Liquid detergent:
Put the SEPARATOR in the front position,
between the guides, as shown following. There will be no gap
between the bottom of the wash cycle detergent
compartment and the bottom of the separator.
■
Powdered detergent:
Put the SEPARATOR in the back
position, behind the guides, as shown following. There will be
a gap between the bottom of the wash cycle detergent
compartment and the bottom of the separator.
NOTE:
The separator will be in the POWDER (back) position
when shipped from the factory.
Bleach compartment
(Number 5 in Dispenser Illustration)
Add NO MORE THAN
¹⁄₃
cup (80 mL) liquid chlorine bleach to this
compartment. The bleach will be automatically diluted and
dispensed at the optimum time during the first rinse after the
wash cycle. This compartment cannot dilute powdered bleach.
■
Always measure liquid chlorine bleach. Use a measuring cup
with a pour spout; do not guess.
■
Do not fill beyond the “MAX” level. Overfilling could cause
severe garment damage.
Fabric Softener compartment
(Number 6 in Dispenser Illustration)
Add ¼ cup (60 mL) liquid fabric softener to this compartment.
Fabric softener will be automatically dispensed in the final rinse.
■
Do not fill beyond the “MAX” level.
Pausing or Restarting
1.
To pause the washer at any time, select PAUSE/CANCEL.
2.
To continue the cycle, select HOLD TO START (for
approximately 1 second).
Changing Cycles, Options and Modifiers
Not all Options and Modifiers are available with all cycles. Cycles,
Options and Modifiers can be changed anytime before HOLD TO
START is selected.
Options and Modifiers can be changed anytime after HOLD TO
START is selected and before the start of the selected Option or
Modifier.
To cancel a cycle and select a new cycle
1.
Select PAUSE/CANCEL twice.
2.
Select desired cycle.
3.
Select the desired OPTIONS.
4.
Select HOLD TO START (for approximately 1 second) to
restart the washer at the beginning of the new cycle.
To cancel a cycle
1.
Select PAUSE/CANCEL twice.
2.
The washer powers down, the door unlocks, and clothes can
be removed.
NOTE:
If the water level or the temperature is too high, the
washer will drain automatically before the door unlocks.
To change Options or Modifiers after the cycle has started
1.
Select PAUSE/CANCEL.
2.
Select the desired OPTIONS or MODIFIERS.
3.
Select HOLD TO START (for approximately 1 second) to
continue the cycle.
To drain the washer manually
1.
Select PAUSE/CANCEL.
2.
Select DRAIN/SPIN.
3.
Select HOLD TO START (for approximately 1 second) to
begin the drain.
4.
When the spin is complete, the door unlocks. Items can be
removed from the washer.
Separator in front position, between guides
1. Separator
2. Guide
Separator in back position, behind guides
1. Separator
2. Guide
LIQUI
SO
1
2
LIQUI
SO
1
2