Filter
Top Products
- Turn the thermostat control to the minimum (MIN) setting. This does not mean
that the iron is switched off permanently.
Service:
- Make sure that the appliance is serviced only by specialist personnel, and
that only original spare parts or accessories are used to replace existing parts/
accessories.
- Any misuse or failure to follow the instructions for use renders the guarantee
and the manufacturer’s liability null and void.
Instructions for use
Before use:
- Remove the appliance’s protective lm.
- Some parts of the appliance have been lightly greased. Consequently, the
rst time the appliance is used a light smoke may be detected.
- Prepare the appliance according to the function you wish to use.
Filling with water:
- It is essential to have lled the deposit with water to be able to work with
steam.
- Open the lid of the lling mouth.
- Fill the deposit taking care to observe the MAX level (Fig. 1)
- Close the lid of the lling mouth.
Use:
- Unroll the cable completely before plugging it in.
- Connect the appliance to the mains.
- Start the appliance by turning on the speed regulator.
- The pilot light (I) comes on.
- Turn the thermostat control to the desired temperature position.
- Do not use temperatures higher than those indicated on the garments to be
treated.
● Temperature for synthetic bres (Polyester, Nylon…).
●● Temperature for silk, wool.
●●● Temperature for cotton. (Minimum temperature for steam ironing)
Max Temperature for linen.
- If garment has various kinds of bres, select the temperature for the bre
that requires the lowest temperature. (For example, select the temperature for
polyester for an article made out of 60% polyester and 40% cotton).
- Wait until the pilot light (I) has gone out which will indicate that the appliance
has reached an adequate temperature.
- During use the pilot light (I) will automatically ash on and off, thus indicating
that the heating elements are operating in order to maintain the desired
temperature.
Dry ironing:
- The appliance has a steam ow regulator (C) that permits dry ironing (without
steam) when placed in the 0 position.
Steam Ironing:
- It is possible to iron with steam whenever the deposit is lled with water and
the adequate temperature is selected.
Steam ow control:
- The appliance has a (C) control knob that allows to get the control of the
steam ow.
Spray:
- The spray can be used in both steam and dry ironing.
- Press the spray button ( A ) to use this operation.
- The spray button has to be pressed repeatedly to release the rst spray.
Steam blast:
- This function proportions extra steam for eliminating wrinkles.
- Press the steam blast button (B). Wait a few seconds until vapour penetrates
the bres of the garment before pushing the button again. For optimum steam
quality, do not apply more than three successive blasts.
- The spray button has to be pressed repeatedly to release the rst spray.
Vertical steaming
It is possible to iron hanging curtains, items of clothing on his hanger, etc. To do
so, follow the instructions:
- Select the maximum temperature of the iron, while turning the temperature
regulator of the iron in a clockwise direction (Fig 2).
- Move the iron in a top to bottom direction while pressing the steam control
( B ). Important: for cotton and linen, its recommended to put the iron base in
contact with the material. For other more delicated bres, it’s recommended to
keep the iron base at some centimetres of distance.
Once you have nished using the appliance:
- Select the minimum position (MIN) using the thermostat control.
- Unplug the appliance to the mains.
- Remove the water from the water tank.
- Clean the appliance
Cleaning
- Disconnect the appliance from the mains and let it cool before undertaking
any cleaning task.
- Clean the equipment with a damp cloth with a few drops of washing-up liquid
and then dry.
- Do not use solvents, or products with an acid or base pH such as bleach, or
abrasive products, for cleaning the appliance.
- Do not submerge the appliance in water or any other liquid, or place it under
a running tap.
Self-cleaning function:
- It is important to self-clean the appliance at least once a month to remove
calcium and any other built-up minerals inside the iron.
- Fill the depository to its maximum level, as indicated on “water ll” section.
- Place the iron in a vertical position, plug in to the mains and select the
maximum temperature.
- Leave the appliance to heat up until the pilot light indicates that it has reached
its consigned temperature.
- Unplug the appliance and place in the sink.
- Press the self-clean button, and keep it pressed down.
- Let the water ow out through the steam vents in the base, while lightly
shaking the appliance.
- Release the button after a minute or when the tank becomes empty.
- Leave the iron in the vertical position until it has cooled.
Anomalies and repair
- Take the appliance to an authorised technical support service if problems
arise. Do not try to dismantle or repair without assistance, as this may be
dangerous.
For EU product versions and/or in case that it is requested in your country:
Ecology and recyclability of the product
- The materials of which the packaging of this appliance consists are included
in a collection, classication and recycling system. Should you wish to dispose
of them, use the appropriate public recycling bins for each type of material.
The product does not contain concentrations of substances that could be
considered harmful to the environment.
This symbol means that in case you wish to dispose of the
product once its working life has ended, take it to an authorised
waste agent for the selective collection of waste electrical and
electronic equipment (WEEE)
This symbol means that surface could to get hot during the use.
This appliance complies with Directive 2006/95/EC on Low Voltage, Directive
2004/108/EC on Electromagnetic Compatibility and Directive 2011/65/EC on
the restrictions of the use of certain hazardous substances in electrical and
electronic equipment.
Manual Aral 2200.indb 9 05/07/13 09:59