Filter
Top Products
14
To use a Manual Cycle
■ Select a Manual Cycle.
■ Press the plus (+) or minus (-) key until the desired drying time
is displayed. Press plus (+) or minus (-) and the time will
change by 1-minute intervals. Press and hold plus (+) or
minus (-) and the time will change by 5-minute intervals.
NOTE: The plus (+) or minus (-) features can be used only
with Manual Cycles.
■ Press TEMP until the desired temperature illuminates.
NOTE: During a Manual Cycle, you can change the settings
for Time, Temperature, Extra Care and Cycle End Tone signal.
Press PAUSE/CANCEL twice to stop the dryer and clear the
settings. Select another cycle or option.
4. (OPTIONAL STEP) If desired, set the
Cycle End Tone signal
.
Select LOUD or SOFT to alert you when a cycle ends.
5. Press and hold START for approximately 3 seconds until
dryer starts. Be sure the door is closed.
■ If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
■ If you wish to end your drying cycle after pressing Start,
press PAUSE/CANCEL twice.
Stopping Your Dryer
To stop your dryer at any time
Press PAUSE/CANCEL twice or open the door.
Pausing or Restarting
To pause the dryer at any time
Open the door or press PAUSE/CANCEL once.
To restart the dryer
Close the door. Press and hold START until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes. If the cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Select new cycle settings before restarting the dryer.
Control Locked
This feature allows you to lock your settings to avoid unintended
use of the dryer. You can also use the Control Locked feature to
avoid unintended cycle or option changes during dryer operation.
To enable the Control Locked feature when dryer is
running:
Press and hold the DRY RACK button for 3 seconds. The control
is locked when a single beep is heard and the Control Locked
icon is displayed in the status window. The icon is located next to
the Dry Rack button and will illuminate when control locked.
■ When the dryer is off, it is not necessary to turn the control on
before activating the Control Locked feature.
To unlock:
Press and hold the DRY RACK button for 3 seconds to turn off
this feature.
NOTE: When the dryer is running and Control Locked is on, the
dryer can be stopped by pressing the PAUSE/CANCEL button,
but can’t be restarted until the control is unlocked.
Drying and Cycle Tips
Select the correct cycle and dryness level or temperature for your
load. If an Automatic Cycle is running, the display shows the
estimated cycle time when your dryer is automatically sensing
the dryness level of your load. If a Manual Cycle is running, the
display shows the exact number of minutes remaining in the
cycle.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
■ Follow care label directions when they are available.
■ Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent
press, knits and synthetic fabrics.
■ Avoid drying heavy work clothes with lighter fabrics. This
could cause overdrying of lighter fabrics, leading to increased
shrinkage or wrinkling.
Cycle tips
■ Dry most loads using the preset cycle settings.
■ Refer to the Automatic or Manual Preset Cycle Settings chart
(in the “Cycles” section) for a guide to drying various loads.
■ Drying temperature and Dryness Level are preset when
you choose an Automatic Cycle. You can choose a
different dryness level, depending on your load by
pressing the DRYNESS LEVEL button to select MORE or
LESS.
■ If you wish to adjust the cycle length of a Manual Cycle,
you must press plus (+) or minus (-) buttons. Adjust the
temperature of a Manual Cycle by pressing TEMP until
the desired temperature is selected.
NOTE: You cannot choose a Dryness Level with Manual
Cycles.
Status Display
Messages on the status display help you to follow the progress of
your dryer.
Wet
WET is displayed at the beginning of the Automatic or Manual
Cycle if a wet item is detected.
■ In an Automatic Cycle, if a wet item is not detected after
5 minutes, the dryer goes directly into Cool Down. COOL
DOWN will be displayed, along with EXTRA CARE, if
selected.
■ In a Manual Cycle, if a wet item is not detected, the dryer will
continue to run for the length of time selected, but WET will
not be displayed.
Damp
DAMP is displayed if the load has reached the damp dry level.
NOTE: DAMP will not be displayed with Manual Cycles.