Filter
Top Products
GAS REQUIREMENTS (GAS MODELS ONLY)
CONNECTING GAS DRYERS
,A WARNING" To reduce the risk of fire,
electric shock, or injury to persons when using
this appliance, follow basic precautions, including
the following:
• Gas supply requirements:
As shipped from the factory, this dryer is configured
for use with (NG) natural gas. It can be converted for
use with LP (Liquefied Propane) gas. Gas pressure
must not exceed 8 inches water column for (NG), or
13 inches water column for (LP).
• A qualified service or gas company technician must
connect the dryer to the gas service. Failure to do so
can result in fire, explosion, or death.
• Isolate the dryer from the gas supply system by clos-
ing its individual manual shutoff valve during any
pressure testing of the gas supply. Failure to do so can
result in fire, explosion, or death.
• Supply line requirements: Your laundry room must
have a rigid gas supply line to your dryer. In the
United States, an individual manual shutoff valve
MUST be installed within at least 6 ft. (1.8 m) of the
dryer, in accordance with the National Fuel Gas Code
ANSI Z223.1 or Canadian gas installation code CSA
B149.1. A 1/8 inches NPT pipe plug must be installed.
Failure to do so can result in fire, explosion, or death.
• If using a rigid pipe, the rigid pipe should be 1/2 inch- •
es IPS. If acceptable under local codes and ordinances
and when acceptable to your gas supplier, 3/8 inches
approved tubing may be used where lengths are less
than 20 ft. (6.1 m). Larger tubing should be used for
lengths in excess of 20 ft. (6.1 m). Failure to do so can
result in fire, explosion, or death.
Connect the dryer to the type of gas shown on the
nameplate. Failure to do so can result in fire, explosion, or
death.
• To prevent contamination of the gas valve, purge the
gas supply of air and sediment before connecting the
gas supply to the dryer. Before tightening the connec-
tion between the gas supply and the dryer, purge
remaining air until the odor of gas is detected. Failure
to do so can result in fire, explosion, or death.
• DO NOT use an open flame to inspect for gas leaks.
Use a noncorrosive leak detection fluid. Failure to do so
can result in fire, explosion, or death.
• Use only a new AGA- or CSA-certified gas supply line
with flexible stainless steel connectors. Failure to do so
can result in fire, explosion, or death.
• Securely tighten all gas connections. Failure to do so
can result in fire, explosion, or death.
• Use Teflon C'_tape or a pipe-joint compound that is
insoluble in Liquefied Petroleum (LP) gas on all pipe
threads. Failure to do so can result in fire, explosion, or
death.
DO NOT attempt any disassembly of the dryer; any
disassembly requires the attention and tools of an
authorized and qualified service person or company.
Failure to do so can result in fire, explosion, or death.
Electrical Requirements for Gas Models Only
• Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord. Failure to
follow this warning can result in fire, explosion, or
death.
• For personal safety, this dryer must be properly
grounded. Failure to follow this warning can result in
fire, explosion, or death.
• The power cord of this dryer is equipped with a
3-prong (grounding) plug which mates with a stan-
dard 3-prong (grounding) wall outlet to minimize the
possibility of electric shock hazard from this appli-
ance. Failure to follow this warning can result in fire,
explosion, or death.
10
This dryer must be plugged into a 120-VAC, 60-Hz.
grounded outlet protected by a 15-ampere fuse or
circuit breaker. Failure to follow this warning can result
in fire, explosion, or death.
Where a standard 2-prong wall outlet is encoun-
tered, it is your personal responsibility and obliga-
tion to have it replaced with a properly grounded
3-prong wall outlet. Failure to follow this warning can
result in fire, explosion, or death.
3-prong
grounding type
a-prong
grounding
plug
Ensure proper
ground exists
before use.