Filter
Top Products
Instructions for installation and use
14
Mounting the Parts onto the
Face of the Machine
- Mount the hinge supports onto
the face of the machine,
positioning the hole indicated by
the arrow in fig. 1 towards the
inside of the face and using the
type C screws.
- Mount the magnetic plate on
the opposite side, at the top,
using the two type B screws.
- Place the spacer illustrated in
fig. 4/B between the appliance
front and the magnet receiver.
Using the Drilling Template
- To trace the positions of the
holes on the left-hand side of the
panel, align the drilling template
to the top left side of the panel
using the lines traced on the
extremities as a reference.
- To trace the positions of the
holes on the right-hand side of
the panel, align the drilling
template to the top right side of
the panel.
- Use an appropriately sized
router to mill the holes for the two
hinges, the rubber plug and the
magnet.
Mounding the Parts onto the
Wooden Panel (Door)
- Insert the hinges into the holes
(the movable part of the hinge
must be positioned facing away
from the panel) and fasten them
with the 4 type A screws.
- Insert the magnet into the top
hole on the opposite side of the
hinges and fasten it with the two
type B screws.
- Insert the rubber plug into the
bottom hole.
The panel is now ready to be
mounted onto the machine.
Mounting the Panel into the
machine
Insert the nib of the hinge
(indicated by the arrow in fig. 2)
into the hole for the hinge and
push the panel towards the front
of the machine. Fasten the two
hinges with the type D screws.
Fastening the plinth guide
If the machine is installed at the
end of a set of modular cabinets,
mount either one or both of the
guides for the base molding (as
shown in fig. 8). Adjust them for
depth based on the position of
the base molding, and, if
necessary, fasten the base to
the guides (fig. 9).
This is how to assemble the
plinth guide (fig.8):
Fig. 6 Fig. 7 Fig. 9
D
C
C
Adjusting the appliance height
The height of the appliance can
be adjusted (from 815 mm to
835 mm), by turning the 4 feet.
Should you require the
appliance to be placed higher
than the above height, you need
to use the following accessories
to raise it to up to 870 mm:
- the two crossbars (G)
- the 4 feet (H)
- the 4 screws (I)
- the 4 nuts (L)
then perform the following
operations (fig. 11):
remove the 4 original feet, place
a crossbar G at the front of the
appliance, fastening it in place
using screws I (screwing them
in where the original feet were)
then insert the new feet H.
Repeat the same operation at
the back of the appliance.
Now adjust feet H to raise or
lower the appliance from 835
mm to 870 mm.
Once you have reached the
desired height, lock nuts L onto
crossbar G.
Fig. 11
L
I
H
G
To adjust the appliance to a
height between 870 mm and 900
mm, you need to mount strip M,
adjusting feet H to the required
height.
Insert the strip as follows:
loosen the three screws N
situated at the front of the Top
cover of the appliance, insert
strip M as shown in fig. 12, then
fasten screws N.
Accessories provided for the
height adjustment
The following can be found inside
the polystyrene lid (fig. 10):
2 crossbars (G),
1 strip (M)
the following can be found inside
the appliance drum:
4 additional feet (H),
4 screws (I),
4 screws (R),
4 nuts (L),
2 plinth guides (Q)
Fasten angle P using screw R,
insert plinth guide Q into the
special slot and once it is in the
desired position, lock it in place
using angle P and screw R.
Inserting the machine into the
Cabinet
- Push the machine into the
opening, aligning it with the
cabinets (fig. 6).
- Regulate the adjustable feet to
raise the machine to the
appropriate height.
- To adjust the position of the
wooden panel in both the
vertical and horizontal
directions, use the C and D
screws, as shown in fig. 7.
Important: close the lower part
of the appliance front by
ensuring that the plinth rests
against the floor.
Fig. 10
Fig. 12
Fig. 8
M
570
m
in
815
540
595
820 ÷ 900
600 m
in