Filter
Top Products
"Power" button
Push the "power" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "power" button to switch on the power. If the
"start/pause" button is not pushed, the machine will
switch off the power automatically after 5 minutes.
WATER LEVEL button
Attention As selecting the water level 1,3,5,7,9;the light
is flashing;
As selecting the water level 2,4,6,8,10;the light
is lighting;
The washing machine can detect the laundries automatically.
After detection,it will set the water level to suitable value among
4, 6, 8,and 10 automatically.
You can also set water level by yourself. After the machine is started,
it will not set water level automatically. You shall push thestart/pause
button to make new setting.
If there's water inside the tub, the machine cannot detect the
laundries and will display water level 6 .
If save program is selected, it will display water level 2 .
When water level 2 is reached in water filling, it will perform
washing while filling water.When water level 3 is reached, it will
change to normal washing.
During operation of wash and rinse program, you can push down
the water level button to add water. When you release the button, or
it reaches the overflow water level, the machine will stop adding
water.
The water level decided may be different from actual value because
of the different moisture level of the laundries.
PROGRAM/RESERVE
WATER
LEVEL
POWER
ON/OFF
LIG
HT
FLASH
Reserve,Process,remain time digitron
It displays "--" during detecting.
It displays remained reserve time (hour).
It displays total remained time (min). If the total time
exceeds 99 minutes, it uses "A" on tens digit to
represent100 minutes, and uses "b" to represent 110
minutes.E.g. "A3" represents 103 minutes.
It displays abnormal symbol in abnormal situation.
(See to Page15)
(HOURS LATER)
(MINUTES)
About less than 2mm after twisting
Figure 3
Connection between the water inlet hose jointer and the water faucet
Bushing
About 4mm before twisting
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen the
four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise
it may leak water.See to Figure 3.)
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
Water faucet,not suitable
Install the water inlet hose
Screw
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
Figure 6
Sign plate
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Figure 2
Screw nut
Screw knife
3.Fasten the four screws evenly. See to Figure 4.
water inlet hose jointer
Figure 5
Outlet end surface
Slider
Figure 1
Water faucet,suitable
water inlet hose
Figure 4
Lock level
Confirm the water faucet
PROGRAM/RESERVE button
Push down the program/ reserve button. You
can select one program of ten which is
standard,soak heavy, gentle,save,cotton,
single wash,rinse spin,single spin,tub clean,
air dry;
Push the"program/ reserve" button to set the
reserve wash program morethan two seconds
continuously;
When the "reserve" function is activated, the
indicator light of the program you have set will
be off. The "reserve (hour)" and "time remain"
indicator lights will be on;
During reserve procedure, push the "reserve"
button to display the reserve mode.To change
the running program or cancel the reserve
setting, you need to switch off the power and
make new selection;
Digital display
Digital display
Fuzzy logic control
Fuzzy logic control
10 water level selection
10 water level selection
Digital display
Digital display
Fuzzy logic control
Fuzzy logic control
10 water level selection
10 water level selection
Digital display
Digital display
Fuzzy logic control
Fuzzy logic control
10 water level selection
10 water level selection
Digital display
Digital display
Fuzzy logic control
Fuzzy logic control
10 water level selection
10 water level selection